Controllers - AGCO Parts

Electronic Pump Control 12 VDC
Regulates motor speed of SHURflo ® and
FloJet ® pumps to achieve a constant liquid
output.
| Part | Description |
| AG056952 | Pump Control |
| AG052822 | Fuse |
SHURflo Power Twin Pump
Take all the performance and features
of the time tested 2088 series,
double it and the result is the high
flow Power Twin. Delivers an open
flow of 7.0 GPM at a mere 9.8 amps.
At 40 PSI it delivers 4.2 GPM and
draws only 19.1 amps. One of the
most efficient high flow self-priming pumps available today, the Power
Twin is excellent for transferring, intermittent duty spraying, and use as
a 1:1 proportioning.
Features:
• Up to 7 GPM
• Self Priming
• Long life pressure switch
• Santoprene ® Diaphragm, Viton valves
• Thermally protected motor with heat sink
• Quiet balanced operation
| Part | Description |
| AG058480 | Pump Power Twin 7 GPM |
| AG427131 | SHURflo 90° Swivel Fitting 1/2" (F) x 3/8" Hose |
| AG427130 | Elbow Swivel Fitting 1/2" MSPT- |
| | Female X 1/2" Hose Barb |
| AG427133 | SHURflo Straight Swivel Fitting 1/2" (F) x 3/8" Hose |
| AG427132 | SHURflo Straight Swivel Fitting 1/2" (F) x 1/2" Hose |
| AG714959 | Filter 1/2" Barb |
| AG427342 | SHURflo Strainer 255-213 |
Mini Line Strainers
These Mini line strainers were developed specifically
for use with SHURflo ® pumps.
Features:
• Direct coupling to pump 1/2" (M) inlet or outlet
• Easy to open oversized cap
• Reinforced stainless steel screens
• Screens available in 32, 50, 80 , and 100 mesh
sizes
• 3/8" Hose barb outlet
| Part | Description |
| AG726406 | Strainer In-Line 32 Mesh |
| AG726407 | Strainer In-Line 50 Mesh |
| AG726408 | Strainer In-Line 80 Mesh |
| AG726409 | Strainer In-Line 100 Mesh |
12V Motor Speed Control
Controller is ideal for use with Hypro's roller
pump/12V motor. Bypass plumbing can be
eliminated in many instances as the pump can
be controlled to deliver only the required volume
by regulating the speed of the motor.
Handles motors up to 36 amp. Glycerin-filled
gauge and 20' wiring harness has extra set of
leads that can be connected to the boom on/off
solenoid. This provides simultaneous on/off
control of pump and boom.
| Part | Description |
| AG051729 | Speed Controller |
Roller Pump and 12V Motor
The Hypro 4101N-H roller pump has 4-rollers
and comes with a Ni-Resist housing made of
high nickel content alloy for better corrosion
resistance. The system is ideal for bulk
chemical transfer, fertilizer placement, herbicide
banding, nitrogen side-dressing, and orchard and cattle spraying.
• Max. flow: 7.2 gpm • Max. pressure 50 PSI continuous
• Viton Seals
• Super Rollers
| Part | Description |
| AG009204 | Hypro Roller Pump & 12 Volt DC Motor |
| AG009457 | Motor Only, 12 Volt DC |
| AG050467 | Pump Only, 4101N-H |
| AG006246 | Pump Repair Kit Super Rollers |
Oil Change System
Features:
• Remove dirty oil through dipstick tube
• Comes complete with all necessary hoses
and oil storage container
• Liquid temperatures from 40 °F to 185°F
• Thermal overload protection
• Built-in reversible switch and 8' cable with
battery clips
• BUNA impeller
Note: Great for use with small engines!
| Part | Description |
| AG717771 | Oil Change System |
Engine-Driven Centrifugal Pumps
Cast iron pumps have nylon impeller, Viton
seal, and Briggs & Stratton or Honda engine.
• 75 GPM at 40 PSI
• Maximum Flow Rate: 100 GPM
• Maximum Pressure: 70 PSI
Notes: 1-1/2" Inlet 1-1/4" Outlet. See the
Technical Pages for more information on
repairs.
| Part | Description |
| AG053712 | Pump, 5-HP B&S |
| AG053711 | Pump, 5.5-HP Honda |
Pumps
81