Controllers - AGCO Parts

Banjo Poly Pedestal Pumps
Poly pedestal pumps may be direct coupled to a
3450 RPM high-speed electric motor or driven by
belt and pulley. A 3/4" keyed shaft is standard.
Note: Coupler not included.
| Part | Description |
| AG002456 | Pump, 2" |
| AG057191 | Pump, 3" |
Banjo Poly Pump Repair Parts
Repair parts for pumps made after September 1996. These parts are for
1-1/2", 2", and 3" pumps, unless otherwise noted.
Notes: * = Repair Kit Items. (**) = This part may not be shown in this
exploded view drawing. (a) = For 1-1/2" Pumps. (b) = For 2" Pumps. (c) =
For 3" Pumps # AG057551 O-Ring prime drain plug (2 per pump) (C).
Banjo Cast Iron Pumps
Banjo cast iron centrifugal pumps
provide quality you can depend on.
Pumps are self priming and are available
in a broad range of sizes from
1½" 3-h.p. to 3" 13-h.p. Features
such as stainless steel shaft sleeve
to protect engine shaft, carbon
ceramic seal with stainless steel
housing are standard. Rubber parts are made of EPDM for better resistance
to agricultural chemicals.
The 2" pump (200PIH5) has the 5-h.p. Honda engine, the 3" pump
(300PI11) has 11-h.p. Honda with electric start. Honda engines boast
features like overhead valves, *Oil AlertTM which automatically stops
engine if oil drops below a safe level, and ball bearing supported crankshaft.
Convenience features such as dual oil drains and fillers are
standard.
Note: Oil AlertTM not available on 11 HP model.
Pumps
| Ref | Part | Description |
| 2 | AG055330 | Body Nuts, S.S., (10 per pump) |
| 3 | AG055331 | Lock Washer, S.S. |
| 4 | AG055323 | Rear Bracket, New |
| 5,6** | AG000741 | Seal Assembly* |
| 7** | AG000744 | Screw Head O-Ring, (4 per pump)* |
| 8 | AG055322 | Bracket Screw, S.S. (4 per pump) |
| 9** | AG000750 | O-Ring Segment* |
| 10** | AG055321 | Body O-Ring* |
| 11** | AG055325 | 3 Vane Poly Pump Impeller, New* (a) |
| 11** | AG055324 | 5 Vane Poly Pump Impeller, New* (b) |
| 11** | AG057556 | 4 Vane Poly Pump Impeller, New* (C) |
| 12 | AG055326 | Impeller Bolt, S.S. (a and b) |
| 12 | AG057555 | Impeller Bolt, S.S (C) |
| 14 | AG055335 | Impeller Hex Nut |
| 15 | AG055327 | Poly Pump Volute, New (a and b) |
| 15 | AG057554 | Poly Pump Volute, New (C) |
| 16 | AG000748 | Volute Screw, S.S. (2 per pump) |
| 17** | AG000738 | Poly Pump Check Valve* |
| 18 | AG055329 | Poly Pump Body Assembly, New (a) |
| 18 | AG055328 | Poly Pump Body Assembly, New (b) |
| 18 | AG057553 | Poly Pump Body Assembly, New (C) |
| 19 | AG000974 | Body Screws, S.S. (10 per pump) |
| 20 | AG055336 | Prime/Drain Plug (2 per pump) (a & b) |
| 20 | AG057552 | Drain Plug |
| 21** | AG050532 | O-Ring, Prime/Drain Plug* |
| | | (2 per pump) (a & b) |
| 21** | AG057551 | O-Ring, Prime/Drain Plug # |
| 25 | AG000945 | Upper Volute Screw, S.S. |
| 26 | AG055334 | Rear Bracket Washer, S.S. (4 per pump) |
| 27 | AG055333 | Impeller Key |
| 28** | AG055337 | Poly Pump Slinger, New* |
| 29** | AG006696 | O-Ring for Seal Assembly* |
| ** | AG059983 | Repair Kit, 1-1/2" and 2" with 3.5 HP Engine |
| ** | AG055982 | Repair Kit, 1-1/2" and 2" with 5 HP Engine |
| ** | AG058076 | Repair Kit, 3" |
| Part | Description |
| AG007178 | 1-1/2" - 3HP Briggs - 100 GPM |
| AG007126 | 2" - 3 HP Briggs - 160 GPM |
| AG005619 | 2" - 5HP Briggs OHV - 160 GPM |
| AG008419 | 2" - 5 HP Honda - 160 GPM |
| AG060324 | 2" with 6HP Vanguard 160 GPM |
| AG717760 | 3" - 8 HP Honda Electric Start |
| AG007920 | 3" - 11 HP Honda Electric Start - 250 GPM |
| AG428346 | 3" - 13 HP Honda Electric Start |
| AG007124 | 2" Less Engine |
| AG007918 | 3" Less Engine |
| AG007177 | Pedestal Pump 2" Cast Iron - 3/4" Shaft |
| AG007919 | Pedestal Pump 3" Cast Iron - 1" Shaft |
| AG057557 | Pedestal Assembly for 1-1/2 & 2" - 3/4" Shaft |
| AG008567 | Pedestal Assembly for 3" - 1" Shaft |
86