C11T- MULTIFUNCTION CNC BOARD Rev. 2 - CNC4PC

More documents

Recommendations

Info

C32 (Rev. 1.1) User ManualMake sure that when you reach the maxspeed in the control software you get 10VDCout (X2). This voltage can vary dependingon many things, including the electricalproperties of parallel port or breakout boardyou are using, the length of the step pulseyour software is delivering, and the normal hior low status of your step pin. Play with thefine tuning pot in the card (X3), the normallyhi or low status of your pin, and the pulsewidth.5.3 Electromechanical relays. (Pin 1 and Pin 16)Electromechanical relays are very flexible because they can be used for AC or DCand come with NO and NC (Normally Open and Normally Closed) positions.ELECTROMECHANICAL RELAYS SPECIFICACTIONSMaximun Current (AC) 7A@240VAC; 10A@125VACMaximun Current (DC) 15A@24VDC; 10A@28VDCTable 2. Electromechanical Relays Specifications.5.4 Microcontroller based driver monitoring system.This board incorporates a microcontroller that runs programs that monitor thedrivers, e-stop and perform other functions.Functions:Revision: 9/14/2010 http://cnc4pc.com/TechDocs/C32R1_1_User_Manual.pdf 12/20
C32 (Rev. 1.1) User Manual Enables and disables the drivers. Monitors E-Stop. Monitors Safety Charge Pump, Monitors the Drivers errors pins. (it only monitors G320/340, G203, G210/201,Viper Servomotor and Dugong servo drives at this time). Indicates the fault source. Indicates the system Status.5.4.1 Configuration DIPSWITCHThe DIPSWITCH allows activating or deactivating the SCHP detection function,and selecting the driver to be monitored. SWITCH 1SWITCH 1 OFF: Delayed enable output (Port 2 Pin 17).SWITCH 1 ON: Non Delayed enable output (Port 2 Pin 17).The enable output will be activated when start the drivers enable process. A delayin the signal activation time could be added by selecting the OFF position in theDIPSWITCH 1. The table below shows the delay time for every supported driver.DRIVERDELAY (Sec.)G320/340 5G203 2G210/201 2Viper/Dugong 5 SWITCH 2SWITCH 2 ON: Activate the SCHP detection functionRevision: 9/14/2010 http://cnc4pc.com/TechDocs/C32R1_1_User_Manual.pdf 13/20
Page 1 and 2: C11T (Rev.2.1) User ManualC11T- MUL
Page 3 and 4: C11T (Rev.2.1) User ManualGeckodriv
Page 5 and 6: C11T (Rev.2.1) User Manual4. Functi
Page 7 and 8: C11T (Rev.2.1) User Manual5. Specia
Page 9 and 10: C32 (Rev. 1.1) User Manual5.2 Varia
Page 11: C32 (Rev. 1.1) User ManualFig. 5. S
Page 15 and 16: C11T (Rev. 2.1) User ManualWhen the
Page 17 and 18: C11T (Rev. 2.1) User ManualFig. 11
Page 19 and 20: C11T (Rev. 2.1) User ManualFig. 16
Page 21 and 22: C11T (Rev. 2.1) User ManualPOSSIBLE
Page 23: C11T (Rev. 2.1) User Manual8. Dimen

C11T- MULTIFUNCTION CNC BOARD Rev. 2 - CNC4PC

Create successful ePaper yourself

Delete template?

Save as template?