User Manual DAP 26 - KME

More documents

Recommendations

Info

$H:\Marketing_Vertrieb\Bedienungsanleitungen ... - KME$

$H:\Marketing_Vertrieb\Bedienungsanleitungen ... - KME$

Attack TimeRelease TimeThis time-constants show the speed of the regulation process inside the compressor /limiter algorithms. A longer ‘Attack’ time will let some peaks pass beforecompression / limiting occurs which may increase the average SPL level while ashort attack time will give more overload protection to the components. The ‘Releasetime’ should be adjusted to the program material used.Speaker and Amp ParameterIn this window you find a level / power calculator.The values entered in this window do not affect the outputs at all but give usefulinformation about the correct threshold level in the dynamic section together with theoutput level of the selected channel.c) NoisegateThe noise gate can be activated by clicking into the grey ‚Bypass’ field. The thresholdslider will occur and the control field will change the colour to green when the noisegate is activated. The operation is easy – just set the threshold level (the minimumsound level above i.e. disturbing background noise). All audio material with a levelbelow the threshold value will be faded out to silence, audio material above thethreshold will not be processed.The parameters ‚Hold Time’ und ‚Close Time’ affect the regulation process. ‘HoldTime’ describes the time the unit „waits“ before fading out signals below the thresholdlevel and the ‚Close time’ describes the speed of the fade-out. Set this constants totaste depending to the program material transmitted.
ˆˆˆˆAppendix – navigation structure on the hardware unitK.M.E. DAP26Preset ConfigurationChoose an option! >PresetselectionPreset: XXActive Preset Preset: XXInputchannelsChoose an option! ¦>PrXX/InputsDelayChoose an option! ¦>PrXX/In/DelayChannel AChoose a Channel ¦>PrXX/In/Del/Ch AValue : 0.00msOK: change value! ˆK.M.E. DAP26PresetinfoK.M.E. DAP26DevicesettingK.M.E. DAP26DeviceinfoChoose an option!‹ ›Choose an option!‹ ›Choose an option!‹DevicesettingsIn-select: AnalogDevicesettingsNet-ID : 1Deviceinfo: S/N123456Deviceinfo: RevisionX.XOK: Change Value ˆ> OK: Change Value Choose an Info Choose an Info ˆ>Presetinfo: AuthorChoose an Info Presetinfo: Pr.-LockDisabledChoose an Info Presetinfo: Ch-NamesInput A: < IN-A>Input B: < IN-B>Choose an Info Presetinfo: Ch-NamesOutput 1: < OUT-1>Output 2: < OUT-2>Choose an Info Presetinfo: Ch-NamesOutput 3: < OUT-3>Output 4: < OUT-4>Choose an Info Presetinfo: Ch-NamesOutput 5: < OUT-5>Output 6: < OUT-6>Choose an Info Choose an option! Choose an option! Choose an option!PrXX/Route/Ch1 PrXX/Out/Delay . PrXX/Out/MutePrXX/Out/Gain. PrXX/Out/Phase .Input AChannel 1.. Channel 1Channel 1.. Channel 1..OK: Change Input ˆChoose a Channel ¦> Choose a channel ¦> Choose a Channel ¦> Choose a channel ¦>PrXX/InputsPrXX/InputsPrXX/InputsPrXX/Out/Del/Ch 1PrXX/Out/Mute/Ch 1 PrXX/Out/Gain/Ch 1 PrXX/OutputMuteGainFilterValue : 0.00ms Value : Mute OFF Value : 0.0 dB Phase : 0 °Choose an option! Choose an option! Choose an option!Choose a Channel ¦>Choose a Channel ¦>PrXX/In/Mute/Ch AValue : Mute OFFPrXX/In/Gain/Ch AValue : -0.0dBPrXX/In/Fil/ChAFilterNr. 1OK: change value! ˆOK: change value! ˆChoose a Filter ¦>PrXX/In/Fil/ChATyp : BypassPrXX/In/Fil/ChAFrequency: 1000HzPrXX/In/Fil/ChAQ : 0.7PrXX/In/Fil/ChAGain : 0.0dBOK: Change value ˆ> OK: Change value OK: Change value OK: Change value ...OK: Change value ˆ> OK: Change value PrXX/Out/FilterChannel 1PrXX/Out/X-overChannel 1PrXX/Out/Dyn/Ch1Typ : LimiterPrXX/Out/Dyn/Ch1Gain : 0.0dBPrXX/Out/Dyn/Ch1Threshold: -6.0dBChoose a channel ¦> Choose a channel ¦> OK: Change value ˆ> OK: Change value OK: Change value PrXX/Out/Fil/Ch1FilterNr. 1PrXX/Out/X-over/Ch1LP-Typ : BypassPrXX/Out/X-over/Ch1LP-Freq. : 1000 HzPrXX/Out/X-over/Ch1LP-Order : 4PrXX/Out/X-over/Ch1HP-Typ : BypassChoose a Filter ¦> OK: Change Value ˆ> OK: Change Value OK: Change Value OK: Change Value PrXX/Out/Fil/Ch1/Fi1Typ : BypassPrXX/Out/Fil/Ch1/Fi1Frequency: 1000HzPrXX/Out/Fil/Ch1/Fi1Q : 0.7PrXX/Out/Fil/Ch1/Fi1Gain : 0.0 dBOK: Change value ˆ> OK: Change value OK: Change value OK: Change value
Page 3 and 4: Functional unitsThe DAP 26 offers a
Page 5 and 6: There is a 10-digit LED bar-graph f
Page 10 and 11: This cable can be used connecting t
Page 12 and 13: HandlingFunctional units (digital)A
Page 14 and 15: Depending to the setting of the par
Page 16 and 17: PEQ IParametric Equalizer Type IFul
Page 18 and 19: High-pass and Low-passTo restrict t
Page 20 and 21: All-pass filters do not change the
Page 22 and 23: Select an installation folder in yo
Page 24 and 25: Installation Problems:• Program c
Page 26 and 27: Example: Connecting two DAP 26 on d
Page 28 and 29: Select a file name for your preset
Page 30 and 31: Attention!If you forget the passwor
Page 32 and 33: About DAP 26The ‚About’ functio
Page 34 and 35: Selecting ‚Yes’ opens the ‚Sa
Page 36 and 37: Signal FlowThe register tabs can be
Page 38 and 39: In this window you can set the time
Page 40 and 41: Filters 1-4 are to be set to the va
Page 42 and 43: As you can see the output channel 1
Page 44 and 45: The ‚Dynamic’ Window displays t
Page 48 and 49: Appendix - Technical DataTechnical
Page 52: Klingenthaler Musikelektronik GmbHA

User Manual DAP 26 - KME

Create successful ePaper yourself

Delete template?

Save as template?