Atlantis 32 Channel Manual - Qvis Security

More documents

Recommendations

Info

4.6.4 VersionDisplay the basic information such as hardware information, software edition,issue data and so on.4.7 Shut down systemRefer to chapter 3.5.8.Picture 4.46 Version50
5 FAQ and maintenance5.1 FAQIf your problems is not listed, please contact your local installer for service.1). The DVR does not boot up normally.Possible reasons are as followed:1 The power supply is not correct.2 Switch power supply line is not in good connection.3 Switch power supply is damaged.4 The program updating is wrong.5 The hard disk is damaged or the hard disk lines are broken.6 The front panel is damaged.7 The main board of the DVR is damaged.2). The DVR reboots automatically or stops working a few minutes afterboot up.Possible reasons are as followed:1 The input voltage is unstable or too low.2 The hard disk is damaged or the hard disk lines are broken.3 The power of the switch power supply is low.4 Frontal video signal is not stable.5 Bad heat radiator or too much dust or bad running circumstance for the DVR.6 The hardware of the DVR is damaged.3). System cannot detect a hard disk.Possible reasons are as followed:1 The hard disk power supply line is not connected.2 The cables of the hard disk are damaged.3 The hard disk is damaged.4 The SATA port of main board is damaged.4). There are no video outputs in single channel, multiple channels andall channels.Possible reasons are as followed:1 The program is not matched. Please update the program.2 The image brightness is all 0. Please restore the default setup.3 There is no video input signal or the signal is too weak.4 The channel protection or the screen protection is set.5 The hardware of the DVR is damaged.51
Page 1 and 2: ATLANTIS 321 U32 ChannelDVRUser’s
Page 3 and 4: Directory1 Welcome ................
Page 5 and 6: 1. WelcomeThank you for purchasing
Page 7 and 8: 5). Connect SATA data wire 6). Conn
Page 9 and 10: Serial NO Key Mark Function16 Playb
Page 11 and 12: 2.7.4 Audio signal outputCommonly t
Page 13 and 14: 2.8.3 Alarm output port relay param
Page 15 and 16: Picture 3.1 System LoginPassword pr
Page 17 and 18: 3.5.2 PlaybackThere are two methods
Page 19 and 20: Button Function Button Function/ Pl
Page 21 and 22: Speed: Set the PTZ rotation range.
Page 23 and 24: 3: ScanThe PTZ can also work on the
Page 25 and 26: Picture 3.18 Color Setting3.5.7 Out
Page 27 and 28: Main menu Sub menu FunctionManageme
Page 29 and 30: Manual: No matter what the present
Page 31 and 32: (Period) Trigger the motion detect
Page 33 and 34: 4.3.4 Alarm inputWhen the system ge
Page 35 and 36: 4.4.2 Encode setupSet the video/aud
Page 37 and 38: (PPPoE setup)Picture 4.19 PPPOEInpu
Page 39 and 40: (DDNS) (dynamic domain name server)
Page 41 and 42: (Enable) Select this to make sure t
Page 43 and 44: 4.4.6 PTZ setupPicture 4.29 PTZ set
Page 45 and 46: 4.5.2 AccountManage the user purvie
Page 47 and 48: 4.5.3 Online UserLook up the networ
Page 49: Clue: means that the hard disk is
Page 53 and 54: 11). The DVR can not control the PT
Page 55 and 56: 21). The storage time is not enough
Page 57 and 58: Appendix 3.Technique parametersType

Atlantis 32 Channel Manual - Qvis Security

Create successful ePaper yourself

Delete template?

Save as template?