KENWOOD TH-78A 144/440 MHz Dual Bander - The Repeater ...

More documents

Recommendations

Info

5) To transmit, press the PTT switch. The DTSS code is sent for about 0.5 second.NoteVoice output is muted during code output.We recommend that you turn off the batterysaver function when you use DTSS.6) Press the F key, then press the 2 key to cancel the DTSS function.NoteAlthough you can select the CTCSS functionsimultaneously in both band, an incoming DTSScode may be lost at certain timings.3 Using DTSS with a RepeaterPressing the PTT switch transmits the DTSS signal after a short delay. The delay helps avoid any malfunction thatmight be caused when the repeaters switching times interrupt the DTSS signal.The normal delay time is 250 milliseconds. When using shift or split channel operation, the delay time is 450milliseconds. You can change the delay time to 250 milliseconds.To Change Delay Time1) Turn the power off.2) Press and hold the 1 key.3) Turn the power on.4) Release the 1 key.PAGINGPaging uses a DTMF (Dual Tone Multi Frequency) signal and is useful in calling members of a group, a specificstation, or for waiting for a call from another station.You should determine the common group paging code and individual codes in advance. You can enter three-digitcodes from 000 to 999.Page 30
Unlike DTSS, the calling station code displays on the transceiver so the receiving party can identify the calling station.If called with an individual code, the individual caller code displays. When called with a group code, the group codedisplays.1 Paging Operation OverviewSet your station codeTune to frequency of the other stationEnter the paging modeSet the code ofstation to be calledTransmitCallStand-by2 Paging Code MemoryThere are 8 paging code memories.MemoryCodeAUseStores your station ID code in memory.0 Automatically stores the calling station'scode during reception. Can temporarily setthe code for the station to be called.1~6 Stores group codes and local stationcodes in memory.3 Setting Paging CodesFirst, you must program your Individual Code into Memory A.1) Press the F key then press the 1 key to enter the Paging mode.2) Press and hold the F key for longer than one second, then press the 1 key to enter the code setting mode.Page 31
Page 1 and 2: KENWOODTH-78A144/440MHz FM Handheld
Page 3 and 4: 9 CALL/VFO Scan ...................
Page 5 and 6: CONTROLS OVERVIEWPage 5
Page 7 and 8: Manganese or Alkaline batteriesFull
Page 9 and 10: Separate VOLUME control functionPre
Page 11 and 12: 5) The transceiver actually changes
Page 13 and 14: 3) Select the desired upper tuning
Page 15 and 16: The time-out-timer function cannot
Page 17 and 18: 3) Use the keypad to select any des
Page 19 and 20: 3) Press the M key, then press the
Page 21 and 22: 4 Scanning Memory ChannelsNoteThe t
Page 23 and 24: 8 VFO / Memory ScanThis function le
Page 25 and 26: For example, repeater A uses 146.00
Page 27 and 28: 3) Release the 2 key.You are now ab
Page 29: The desired band will now operate i
Page 33 and 34: 4 Sending Pages (Calling)1) Turn to
Page 35 and 36: 3) Press the PTT switch to respond
Page 37 and 38: Relationship between input characte
Page 39 and 40: Press and hold the M key for longer
Page 41 and 42: 3) Connect your earphone to the Ext
Page 43 and 44: 1) Turn the POWER switch off2) Pres
Page 45 and 46: 2 With the Tuning control, set the
Page 47 and 48: DTMF2SEARMSG M1MSG MXMSGCLROPG OFFO
Page 49 and 50: 1. Installing the CTCSS Unit (TSU-7
Page 51 and 52: To reset the function of the transc

KENWOOD TH-78A 144/440 MHz Dual Bander - The Repeater ...

Create successful ePaper yourself

Delete template?

Save as template?