KENWOOD TH-78A 144/440 MHz Dual Bander - The Repeater ...

More documents

Recommendations

Info

In this mode, the microphone sensitivity and receive audio are reduced automatically to prevent howling. Thetransmitter output power is also automatically set to the EL position. You can select the desired transmitter outputpower by pressing the F key, then pressing the D/LOW key.To cancel this function, repeat the procedure for setting the function. The DUP indicator disappears from the display.POWER ON MESSAGES AND FUNCTION MESSAGE1 Power On MessageWhen you first switch the POWER on, "TH 78A" appears on the display for two seconds. You can change thisfactory-set message to your own message as follows:Changing Power-On Message1 Select your message by following steps 1 to 4 of the memory write procedure on page 36.2 Press the 0 key.The power-on message has now been changed. If you switch the power off and on again, your own messagewill be displayed on the display for two seconds.NoteThe above message, which is stored in message memory channel0, appears each time youswitch the power on.2 Function MessageWhen you select a function, the corresponding function message is displayed on the LCD for two seconds. Themessage and functions are listed below:AF CHGAF INIAF MIXAF SEPAS OFFAS ONBELL 1BELL 2BP OFFBP ONDTMF0STranspose the two AF bandsInitial AF output settingMix the AF output from both bandsSeparate the AF output into two bandsAutomatic offsets OFFAutomatic offsets ONTone alert (Telephone type ring)Tone alert (Tone alarm)Beep OFFBeep ONNo DTMF signal transmission delay timePage 46
DTMF2SEARMSG M1MSG MXMSGCLROPG OFFOPG ONPROGSCNPROGVFOSHIFTSPSPLITUHF COUHF TOVFOCLRVHF COSetting DTMF signal transmission delay time (2 seconds)Earphone modeStore receive messages in up to 10 memory channels.If more than 10 messages are received, the oldest messages are replaced with the new ones.Message transmission memory clearSignal squelch ONCanceling signal squelchProgrammable scan range setting and recallProgrammable VFO tuning limit settingShift width setting modeExternal speaker modeSplit memory channel modeUHF band carrier operate scan modeUHF band time operate scan modeVFO resetVHF band carrier operate scan modeVHF TOVHF band time operate scan mode250MSThe time delay for DTMF code transmission is 250mS450 MS The time delay for DTMF code transmission is 450mSPage 47
Page 1 and 2: KENWOODTH-78A144/440MHz FM Handheld
Page 3 and 4: 9 CALL/VFO Scan ...................
Page 5 and 6: CONTROLS OVERVIEWPage 5
Page 7 and 8: Manganese or Alkaline batteriesFull
Page 9 and 10: Separate VOLUME control functionPre
Page 11 and 12: 5) The transceiver actually changes
Page 13 and 14: 3) Select the desired upper tuning
Page 15 and 16: The time-out-timer function cannot
Page 17 and 18: 3) Use the keypad to select any des
Page 19 and 20: 3) Press the M key, then press the
Page 21 and 22: 4 Scanning Memory ChannelsNoteThe t
Page 23 and 24: 8 VFO / Memory ScanThis function le
Page 25 and 26: For example, repeater A uses 146.00
Page 27 and 28: 3) Release the 2 key.You are now ab
Page 29 and 30: The desired band will now operate i
Page 31 and 32: Unlike DTSS, the calling station co
Page 33 and 34: 4 Sending Pages (Calling)1) Turn to
Page 35 and 36: 3) Press the PTT switch to respond
Page 37 and 38: Relationship between input characte
Page 39 and 40: Press and hold the M key for longer
Page 41 and 42: 3) Connect your earphone to the Ext
Page 43 and 44: 1) Turn the POWER switch off2) Pres
Page 45: 2 With the Tuning control, set the
Page 49 and 50: 1. Installing the CTCSS Unit (TSU-7
Page 51 and 52: To reset the function of the transc

KENWOOD TH-78A 144/440 MHz Dual Bander - The Repeater ...

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?