Mitutoyo1001 Catalog.pdf - JW Donchin CO.

ABSOLUTE Digimatic Indicator ID-CSERIES 543 — with Green/Red LED and GO/NG Signal Output FunctionTechnical DataAccuracy: Refer to the list of specificationsResolution: 0.001mm, .00005”/0.001mm or.0001”/0.001mmDisplay: LCDLength standard: ABSOLUTE electrostatic capacitance typelinear encoderMax. response speed: UnlimitedMeasuring force: 2.0N or lessDust/Water protection level: IP54FunctionData output (–NG/OK/NG signal, NPN open collector),Runout value holding, Counting direction switching, PowerON/OFF, inch/mm conversion (on inch/metric models only)Alarm: Low voltage, Counting value composition error,Over-flow error, Tolerance limit setting errorOptional Accessories902011: Spindle lifting lever* (ISO/JIS type)902794: Spindle lifting lever* (ANSI/AGD type)540774: Spindle lifting cable* (Stroke: .4” / 10mm)125317: Rubber boot––––––: Backs (See page F-32.)––––––: Contact points (See page F-33.)*When using the spindle lifting lever/cable, IP54 is not guaranteed.Output patternWire – NG OK + NG Composition errorOrange (– NG) Low High High HighGreen (OK) High Low High HighBrown (+ NG) High High Low HighLED Red Green Red Red (blinking)LCD < O > “ x.xxE” indicationI/O SpecificationsWire Signal I/O DescriptionBlack – V (GND) — Connected to minus (-) terminalRed + V (GND) I Power supply (12 - 24VDC)Orange – NG O Tolerance judgment resultGreen OK Ooutput: Only the terminalcorresponding to a judgmentBrown + NG O result is set to the below level.YellowPRESET_RECALLZEROIBlue HOLD_RESET IExternal input terminal: If therelevant terminal is set to the lowlevel, its signal becomes true.Shield FG — Connected to GNDFEATURESthe signal ID-C can output the signal of thevalues set. Substitute for the mechanical/electrical contact, the judgment is carriedout by calculating the measurement dataobtained. This provides high reliability withno deterioration of the contact point andvolume adjustment.device like a sequencer through the NPNopen-collector.indicated by the green/red LED and the "" signs on LCD.ABSOLUTE linear encoder,the Signal ID-C always displays the spindle"Absolute Position" from the origin atpower-on.SPECIFICATIONSInch/Metricø54510.62028.5ø60.52049.6ID-C achieves the IP54protection level to resist dust andcontaminants for safe operation in harshmachine shop environments.Resolution Range Order No. (w/ lug, flat-back) Model Accuracy Measuring force.00005”/0.001mm .5” / 12.7mm 543-282 543-282B ID-C112JE .00012” 2.0N or less.0005”/0.01mm .5” / 12.7mm 543-283 543-283B ID-C112JT .00012” 2.0N or lessInch/MetricMetricResolution RangeStem ø 8mm, M2. x 0.45 ThreadOrder No. (w/ lug, flat-back) Model Accuracy Measuring force0.001mm 12.7mm 543-280 543-280B ID-C112J 0.003mm 2.0N or lessDIMENSIONSStem dia. 3/8" #4-48 UNF ThreadStem ø 8mm, M2.5 x 0.45 Threadø10.5ISO/JIS type4m, ø5mm,Core wire AWG/24543-282ANSI/AGD typeResolution Range Order No. (w/ lug, flat-back) Model Accuracy Measuring force.00005”/0.001mm .5” / 12.7mm 543-281 543-281B ID-C112JM .00012” 2.0N or lessUnit: mm( )ANSI / AGD Typeø6.5167.6M2.5×0.45(#4-48UNF)ø8 0-0.0093/8”7.3(6.35)37.2 (37.05) 13.5(11.2)43.5 (41.2)67.4 (64.95)80.7 (78.25)US-1001F-7