Assembly Instructions - Swing-N-Slide

More documents

Recommendations

Info

Assembly InstructionsAnchor-ItFig. 60Fig. 60aFlat Washermetal strap1-1/2"lag boltAnchor-ItAnchor-It Installation.Instructions for Anchoring Swing•N•Slide Activity Centers1. Determine the final location of your activity center.2. Place the Anchor-It stakes adjacent to the base and near the corners of your activity center (at the bottom of thelegs on swing sets) and twist the auger-style stakes into the ground until only the loop is exposed.3. Place the metal strap through the loop of the Anchor-It stake and secure it to the unit with a lag screw andwasher as illustrated to the right. Note: Attach the strap to the unit with as little play as possible using whateverholes in the strap that work best.58
TheOUTRIGGERSEAT ASSEMBLY.Fig. 1Assembly Instructions(2) 1-1/4'' screwsBolt Cover1. Place a rod cap on a hard surface. Insert steelrod into cap and tap into cap with a hammer.2. Insert the seat section into the handle section asshown in (Fig. 2). Make certain the wedge formof the seat points towards the center of the unit.Line up the holes and insert the steel rod throughthe holes.3. Turn the assembly on its side and support thecap/rod assembly with a scrap piece of lumberor dowel and carefully tap a rod cap on theopposite end using a hammer. Repeat steps forother seat.FOOT REST ASSEMBLY.1. Place one 5/16'' washer and nut on the rodassembly (Fig. 2). While holding rod with pliers,tighten nut until the end of the nut is flush withblack plastic cap (Approx.3 ⁄16").NOTE: Do not over tighten, this will cause blackcap to tear.Fig. 215-5/8'' Outrigger Pin5-7/8'' Seat PinPush Cap5/16'' WasherLoc Nut2. Insert the footrest section into the body section asshown in (Fig. 2). Line up the holes and insertthe steel rod through the holes.3. Repeat step 1 while holding other end with awrench or pliers.CHAIN ASSEMBLY.1. Slip one end of the chain over the eyebolt(Fig 3). Place through the seat.2. Place one 1/4'' washer and nut on the eye boltassembly (Fig. 3). Tighten nut until the end of thenut is flush with black plastic cap (approx. 3⁄16").Repeat for all (4) connections.NOTE: Do not over tighten, this will cause blackcap to tear.3. Hang the chains from the swing hangers andcrimp the hooks closed with pliers to secure thechain to the swing hangers.Fig. 3Dipped ChainWasherLoc NutEye Bolt4. Place bolt covers over the top of the swinghangers and loc nuts. Secure to the supportsusing two 1-1/4'' screws per bolt cover (Fig. 1).59
Page 1 and 2:
NOTE: USE THIS PLAN ONLY TO BUILD E
Page 3 and 4:
This product is intended for single
Page 5:
R(2) Shelf-Loc(2) Split Beam bracke
Page 9 and 10: How to select the correct fastenerA
Page 11 and 12: Assembly InstructionsTIMBERGLOVE AP
Page 13 and 14: 4'' x 4'' x 120''Assembly Instructi
Page 15 and 16: DO NOT USE LAGSCREWS HEREUse Lag Sc
Page 17 and 18: Assembly InstructionsFig. 8(3)2-1/2
Page 19 and 20: Assembly InstructionsFig. 10(2)2-1/
Page 21 and 22: Assembly InstructionsFig. 12Fig. 13
Page 23 and 24: Assembly InstructionsFig. 163-3/4''
Page 25 and 26: Fig. 17bAssembly Instructions4'' x
Page 27 and 28: Fig. 18Align the edges of the 4" x
Page 29 and 30: Assembly InstructionsA-Frame Assemb
Page 31 and 32: Assembly InstructionsFig. 25NOTE:Se
Page 37 and 38: Assembly InstructionsFig. 37 Fig. 3
Page 41: Assembly InstructionsFig. 435/4'' x
Page 44 and 45: Assembly InstructionsFig. 46NOTE: 1
Page 48 and 49: Assembly InstructionsFig. 51(8)3/4'
Page 52 and 53: A-Frames Spaced40-1/2''Apart(Outsid
Page 54 and 55: Assembly InstructionsFig. 56MountBr
Page 60 and 61: Assembly InstructionsOptional Disc
Page 62 and 63: Assembly Instructions62
Page 64: Questions???...Call our Customer Se
show all

Assembly Instructions - Swing-N-Slide

Create successful ePaper yourself

Delete template?

Save as template?