INFP - INFINITY Process Panel Meter DC Current ... - NEWPORT

More documents

Recommendations

Info

2 UnpackingUnpack all items and make sure that every item on the packing list ispresent. The items you should receive are listed below. If something ismissing, use the phone number for the Customer Service Departmentnearest you.Also, inspect the shipping container and enclosed equipment for any signs ofdamage. Take particular note of any evidence of rough handling in transit.Immediately report any damage to the shipping agent.Note ☞NOTE: The shipping agent will not honor any claims unless all shippingmaterial is saved for their examination. After examining and removingcontents, save all packing material and containers in the event thatreshipment is required.When you ordered your process meter, you will receive the following items inthe shipping box:QTY DESCRIPTION ILLUSTRATION1 Basic Meter in a MountingSleeve with Gasket1 Front-Panel Button CoverAC Power Connector(orange - P1)123P1LN2 Input Connectors(gray - P3 and P9)1234
Unpacking 21 Rear ProtectiveCover with Screw1 20-Socket RibbonConnector(P2 Connector)2 Panel-MountingGaskets (1 Spare)1 Process Owner’s Guide1 Quick Start ManualOther items may also be in the box depending on the options ordered. Referto specific options described previously.5
Page 2: Additional products fromNEWPORT Ele
Page 7 and 8: Table of ContentsSECTION 19 FACTORY
Page 9 and 10: FiguresFigure 7-9 DC Connector Wiri
Page 11 and 12: Introduction 11.1 DESCRIPTION1.2 FE
Page 13: Introduction 1SERIAL COMMUNICATIONS
Page 17 and 18: Parts of the Meter 44.1 FRONT OF TH
Page 19 and 20: Parts of the Meter 4ITEMDESCRIPTION
Page 21: Parts of the Meter 4P2 / CABLE CONN
Page 29 and 30: Setup 55.2.4 How to Access JumpersT
Page 31 and 32: Setup 5P7P6P10ADBCES1PIN 1Figure 5-
Page 33 and 34: Setup 5S5AS4BACEGABS8S1AS2AJ20PIN 1
Page 35 and 36: Setup 5WARNING: Do not “turn-on
Page 37 and 38: VOLTAGE - UNIPOLARJumpers for 0 to
Page 39 and 40: Jumper Positions 6DISPLAYBDDCBS3ASI
Page 41 and 42: Signal and Power Input Connections
Page 43 and 44: Signal and Power Input Connections
Page 45 and 46: Scaling to Display Engineering Unit
Page 65 and 66:
Scaling to Display Engineering Unit
Page 67 and 68:
Meter Function Menus 9EXPLANATION O
Page 69 and 70:
Meter Function Menus 9MENU MIN/MAX*
Page 71 and 72:
Meter Function Menus 9MENU MIN/MAX*
Page 73 and 74:
Meter Function Menus 99.2 METER FUN
Page 75 and 76:
Meter Function Menus 99.2.3 RDG SC
Page 77 and 78:
9.2.4 IN CNF (Input Configuration)I
Page 79 and 80:
Meter Function Menus 9** The ‘MIN
Page 81 and 82:
Meter Function Menus 99.2.7 CNT BY
Page 83 and 84:
Meter Function Menus 99.2.9 FIL TI
Page 85 and 86:
Meter Function Menus 9* The ‘MIN
Page 87 and 88:
Meter Function Menus 99.2.12 AL FNC
Page 89 and 90:
Meter Function Menus 99.2.14 SP DB
Page 91 and 92:
Meter Function Menus 99.2.17 OT.SC.
Page 93 and 94:
Meter Function Menus 99.2.19 SERCNF
Page 95 and 96:
Meter Function Menus 9MENU MIN/MAX/
Page 97 and 98:
Meter Function Menus 9* The ‘MIN
Page 99 and 100:
SETPOINTS/ALARMSSetpoints/Alarms 10
Page 101 and 102:
Setpoints/Alarms 1010.2 UNLOCKING T
Page 103 and 104:
Setpoints/Alarms 10SP3 = 100SP1-SP3
Page 105 and 106:
Setpoints/Alarms 107. “ALC.7=0”
Page 107 and 108:
Setpoints/Alarms 1010.10 “OUT.CNF
Page 109 and 110:
ANALOG OUTPUT OPTIONAnalog Output O
Page 111 and 112:
Analog Output Options 124. Store th
Page 113 and 114:
Analog Output Options 1212.6 FILTER
Page 115 and 116:
BCD Option 13Figure 13-2 shows the
Page 117 and 118:
BCD Option 1313.4 50-LINE CABLE COM
Page 119 and 120:
BCD Option 1313.11 SELECT DATA POLA
Page 121 and 122:
Relay Options 14Figure 14-2 below s
Page 123 and 124:
RS-232 or RS-485 Option Board 1515.
Page 125 and 126:
RS-232 or RS-485 Option Board 1515.
Page 127 and 128:
External Control Lines 1616.3 VALLE
Page 129 and 130:
Troubleshooting 17TROUBLESHOOTING -
Page 131 and 132:
“ERR 02”POSSIBLE CAUSE:TO CORRE
Page 133 and 134:
Specifications 1818.1 CURRENT INPUT
Page 135 and 136:
POWER RATING FORRESISTIVE LOADS:DUA
Page 137 and 138:
FLASHING MESSAGESDURING PROGRAMMING
Page 139 and 140:
Decimal Point “DEC PT” Position
Page 141 and 142:
JUMPER POSITIONS:CurrentS1: _______
Page 143 and 144:
Record your Setup Values 20Output S
Page 145:
For immediate technical or applicat
show all

INFP - INFINITY Process Panel Meter DC Current ... - NEWPORT

Create successful ePaper yourself

Delete template?

Save as template?