INFP - INFINITY Process Panel Meter DC Current ... - NEWPORT

More documents

Recommendations

Info

5 SetupDISPLAYBD<strong>DC</strong>BS3ASIGNAL INPUT BDR39MAIN BDAS4BCT1J2J9J3W2W3W1AC POWER BDJ1Figure 5-6. ac-Powered Main BoardS1A BAS51APINS FOR RS 4851 11ALL PINS FOR RS232ADETAIL ASEEDETAIL AJ10J21AR34S4J11S51 10J12PINS FORANALOG OUTPINS FOR RELAYAS4S3A B C DS3Figure 5-7. dc-Powered Main Board20
Setup 5P7P6P10ADBCES1PIN 1Figure 5-8. Relay Option Board4 RELAY BOARDPIN 1 OF CABLEJ10MAIN BOARDPIN 1Figure 5-9. 4-Relay Option BoardNote ☞NOTE: Both the Dual Relay Output Board and the 4 Relay Output Board canbe installed at J10. However, only one option board can be installed at atime.21
Page 2: Additional products fromNEWPORT Ele
Page 7 and 8: Table of ContentsSECTION 19 FACTORY
Page 9 and 10: FiguresFigure 7-9 DC Connector Wiri
Page 11 and 12: Introduction 11.1 DESCRIPTION1.2 FE
Page 13 and 14: Introduction 1SERIAL COMMUNICATIONS
Page 15 and 16: Unpacking 21 Rear ProtectiveCover w
Page 17 and 18: Parts of the Meter 44.1 FRONT OF TH
Page 19 and 20: Parts of the Meter 4ITEMDESCRIPTION
Page 21: Parts of the Meter 4P2 / CABLE CONN
Page 29: Setup 55.2.4 How to Access JumpersT
Page 33 and 34: Setup 5S5AS4BACEGABS8S1AS2AJ20PIN 1
Page 35 and 36: Setup 5WARNING: Do not “turn-on
Page 37 and 38: VOLTAGE - UNIPOLARJumpers for 0 to
Page 39 and 40: Jumper Positions 6DISPLAYBDDCBS3ASI
Page 41 and 42: Signal and Power Input Connections
Page 43 and 44: Signal and Power Input Connections
Page 45 and 46: Scaling to Display Engineering Unit
Page 67 and 68: Meter Function Menus 9EXPLANATION O
Page 69 and 70: Meter Function Menus 9MENU MIN/MAX*
Page 71 and 72: Meter Function Menus 9MENU MIN/MAX*
Page 73 and 74: Meter Function Menus 99.2 METER FUN
Page 75 and 76: Meter Function Menus 99.2.3 RDG SC
Page 77 and 78: 9.2.4 IN CNF (Input Configuration)I
Page 79 and 80: Meter Function Menus 9** The ‘MIN
Page 81 and 82:
Meter Function Menus 99.2.7 CNT BY
Page 83 and 84:
Meter Function Menus 99.2.9 FIL TI
Page 85 and 86:
Meter Function Menus 9* The ‘MIN
Page 87 and 88:
Meter Function Menus 99.2.12 AL FNC
Page 89 and 90:
Meter Function Menus 99.2.14 SP DB
Page 91 and 92:
Meter Function Menus 99.2.17 OT.SC.
Page 93 and 94:
Meter Function Menus 99.2.19 SERCNF
Page 95 and 96:
Meter Function Menus 9MENU MIN/MAX/
Page 97 and 98:
Meter Function Menus 9* The ‘MIN
Page 99 and 100:
SETPOINTS/ALARMSSetpoints/Alarms 10
Page 101 and 102:
Setpoints/Alarms 1010.2 UNLOCKING T
Page 103 and 104:
Setpoints/Alarms 10SP3 = 100SP1-SP3
Page 105 and 106:
Setpoints/Alarms 107. “ALC.7=0”
Page 107 and 108:
Setpoints/Alarms 1010.10 “OUT.CNF
Page 109 and 110:
ANALOG OUTPUT OPTIONAnalog Output O
Page 111 and 112:
Analog Output Options 124. Store th
Page 113 and 114:
Analog Output Options 1212.6 FILTER
Page 115 and 116:
BCD Option 13Figure 13-2 shows the
Page 117 and 118:
BCD Option 1313.4 50-LINE CABLE COM
Page 119 and 120:
BCD Option 1313.11 SELECT DATA POLA
Page 121 and 122:
Relay Options 14Figure 14-2 below s
Page 123 and 124:
RS-232 or RS-485 Option Board 1515.
Page 125 and 126:
RS-232 or RS-485 Option Board 1515.
Page 127 and 128:
External Control Lines 1616.3 VALLE
Page 129 and 130:
Troubleshooting 17TROUBLESHOOTING -
Page 131 and 132:
“ERR 02”POSSIBLE CAUSE:TO CORRE
Page 133 and 134:
Specifications 1818.1 CURRENT INPUT
Page 135 and 136:
POWER RATING FORRESISTIVE LOADS:DUA
Page 137 and 138:
FLASHING MESSAGESDURING PROGRAMMING
Page 139 and 140:
Decimal Point “DEC PT” Position
Page 141 and 142:
JUMPER POSITIONS:CurrentS1: _______
Page 143 and 144:
Record your Setup Values 20Output S
Page 145:
For immediate technical or applicat
show all

INFP - INFINITY Process Panel Meter DC Current ... - NEWPORT

Create successful ePaper yourself

Delete template?

Save as template?