Aaton 35 - Panavision

More documents

Recommendations

Info

4.1 CAMERA CONFIGURATIONSThe AATON 35-III is designed to be easily converted between the followingtwo accessory configurations:4.1.1 15mm Front RodsThe most versatile and popular configuration for accessorizing theAATON 35-III, the universal 15mm screw-in front rod system caninstantly accept Aaton, Arri, Chrosziel, Petroff and other manufacturers’mattebox and follow focus system.Utilizing the front rod system allows for quick conversion from tripodto shoulder operating modes without the need for reconfiguration.Aaton manufactures 50mm and 120mm length rods that screwdirectly into the front housing of the AATON 35-III under the lensport.The 15mm front rod system is recommended when standard sizelenses and accessories are to be used or when quick conversion betweentripod and handheld modes is necessary.4.1.2 Sliding Bridgeplate54
THE AATON SYSTEMThe AATON 35-III can also accept standard 15 and 19mm slidingbridgeplates for building the camera system for high-end studiowork. The bridgeplate configuration can accept Aaton, Arri, Chroszieland other manufacturer’s mattebox, follow focus and supportequipment that is designed for bridgeplate use.Standard bridgeplates from Aaton, Arri and other manufacturers canbe attached to the AATON 35-III by means of the 3/8-16 tripodrecepticle on the underside of the camera.The sliding bridgeplate system is recommended when large 35mmlenses and accessories are to be used and when the use of a gearedhead is necessary.4.2 HANDGRIPThe AATON 35-III body includes a wooden handgrip, short 15mmrods, rod coupler and Lemo2 cable as standard. The handgrip which isdesigned to be used for comfortable handheld operation, can also be usedto provide on/off control on the motor side of the camera while on thetripod.4.2.1 Mounting the HandgripScrew in one 15mm short rod in each of the two recepticles on thefront housing of the camera below the lens port. Slide the couplerover the two rods to the desired location and fasten the center wingnut to secure the coupler in position. Attach the handgrip to thecoupler by mating the starplate on the coupler to that on the handgrip,adjusting to the desired position and fastening the T screw ofthe handgrip. Connect the Lemo2 cable between the handgrip andcamera body to add on/off capability to the handgrip. The Lemo2connector is located on the motor side of the camera, (between thetwo motors), under the Lemo8 and Lemo6 connectors.4.2.2 Hangrip On/Off FunctionsBoth camera run and test functions are available from the handgrip.55
Page 1:
35-IIIUser’s GuideJune 97
Page 4 and 5: The AATON 35-III User GuideAATON2 r
Page 7 and 8: TABLE OF CONTENTMenu Operations 423
Page 9: TABLE OF CONTENT8 AATONCODE8.1 Conc
Page 12: 123456789101.1 FRONT1 Eyepiece2 Fri
Page 15 and 16: GENERAL OVERVIEW3132333536343738394
Page 19 and 20: 2THE CAMERA BODY19
Page 21 and 22: THE CAMERA BODYMitchell type dolly,
Page 23 and 24: THE CAMERA BODY-use this reference
Page 25 and 26: THE CAMERA BODYof the camera is set
Page 27 and 28: THE CAMERA BODYWhen the adjustment
Page 29 and 30: THE CAMERA BODYto readjust the prec
Page 31 and 32: THE CAMERA BODYbody. When snug, tig
Page 33 and 34: THE CAMERA BODYenables the body to
Page 35 and 36: THE CAMERA BODYton ot by rotating t
Page 37 and 38: THE CAMERA BODYTo set the camera to
Page 39 and 40: THE CAMERA BODY2.10.4 Low Battery I
Page 41 and 42: THE CAMERA BODYnecessary, clean thi
Page 43: THE CAMERA BODYTechnical allows you
Page 46 and 47: 3.1 CONCEPTThe Aaton magazine has b
Page 48 and 49: • Remove the film from its can an
Page 50 and 51: 50the take-up core indicating that
Page 53: 4THE AATON SYSTEM53
Page 57 and 58: THE AATON SYSTEMadditional padding
Page 59: THE AATON SYSTEMlocated in its base
Page 62 and 63: 5.1 LENSLens Cleaning TipsAvoid han
Page 64 and 65: the body. Remove the viewing screen
Page 67 and 68: 6SUPER3567
Page 69 and 70: SUPER35cal “reduction and axis sh
Page 71: SUPER3571
Page 74 and 75: 7.1 CONCEPTThe only thing we know a
Page 77 and 78: 8AATONCODE77
Page 79 and 80: AATON CODEframe) for 8 hours.The ca
Page 81 and 82: AATON CODEAATONCODEAfter initializa
Page 83: AATON CODEcheck that all diodes are
Page 86 and 87: 9.1 TECHNICAL SPECIFICATIONSWeight
Page 88 and 89: 1.85ACAD + TVTRANS + TV safe +1.661
Page 91 and 92: 10WORLDWIDE SUPPORT91
Page 93 and 94: WORLDWIDE SUPPORTGermanyDEDO WEIGER
Page 95: WORLDWIDE SUPPORTAbelCine Tech / NY
Page 98 and 99: 3-Perf 2.6, 7, 7.1, 7.2, 9.1AatonCo
Page 100 and 101: 100
show all

Aaton 35 - Panavision

Create successful ePaper yourself

Delete template?

Save as template?