Sipura SPA3000 User Guide - MyNetFone

More documents

Recommendations

Info

oNote: The user names for both administrator and User are fixed and cannot be changed.o After making changes to SPA configuration parameters, pressing “Submit All Changes”button will apply all the changes and if necessary, automatically reboot the device. Multiplechanges may be made on multiple page tabs of the web interface at the same time. Pressing“Submit All Changes” will apply all the modifications.oImportant Note: switching between page tabs won’t apply the changes to SPA, The only wayto apply the changes is to press the “Submit All Changes” button.If the “Undo All Changes” button is clicked, any modifications to profile parameters on any andall pages will be reset back to their original values before modification.NOTE: Pressing the “Undo All Changes” has no effect on the SPA; it will only reset thevalues on the web page.3.3.2. Administration PrivilegesThe SPA supports two levels of administration privileges: Administrator and User, both privileges canbe password protected. Important note: by factory default, there are no passwords assigned for bothAdministrator and User.The Administrator has the privilege to modify all the web profile parameters and can also modify thepasswords of both Administrator and User. A User only has the privilege to access part of the webprofile parameters; the parameter group that User can access is specified by the Administrator, whichcan only be done through provisioning.To access the Administrator level privilege, use URL: http://IP_Address_Of_SPA/admin/. If thepassword has been set for Administrator, the browser will prompt for authentication. The usernamefor Administrator is “admin” and cannot be changed.To access the User level privilege, use URL: http://IP_Address_Of_SPA/. If the password has beenset for User, the browser will prompt for User authentication. The username for User is “user” andcannot be changed.When browsing Administrator pages, one can switch to User privileges by click the link “User Login”.(Note: if User password was set, the browser will prompt for User authentication when you click “UserLogin” link). On the other side, from the User pages you can switch to Administrator privilege byclicking the link “Admin Login.” Authentication is needed if Administrator password has been set.Warning: Switching between the User and Administrator will discard the uncommitted changes thathave already been made on the web pages.3.3.3. Basic and Advanced ViewsThe web configuration interface provides a Basic and an Advanced view from which the variousconfiguration parameters can be accessed. The SPA Provisioning tab is only visible from theAdvanced Administrator view of the web interface.Warning: Switching between the basic and advanced view will discard the uncommitted changes thathave already been made on the web pages.3.3.3.1. Resync URLThrough Resync URL you can force the SPA to do a resync to a profile specified in the URL.Note: The SPA will resync only when it is idle.The syntax of Resync URL is:© 2003 - 2004 Sipura Technology, Inc Proprietary (See Copyright Notice on Page 2) 12
http:///resync?[[protocol://][server-name[:port]]/profile-pathname]If no parameter follows “/resync?”, the profile rule setting in provisioning is used. See Error!Reference source not found. for detailed information about profile rule in provisioningIf no protocol is specified, TFTP protocol is assumed. Note: Only TFTP is supported in the currentrelease.If no server-name is specified, the host that requests the URL is used as server-name.If no port specified, default port of the protocol is used – 69 for TFTP.The profile-path is the path to the new profile to resync with.For example: http://192.168.2.217/upgrade?tftp://192.168.2.251/spaconf.scf3.3.3.2. Reboot URLThrough the Reboot URL, you can reboot the SPA.Note: Upon request, the SPA will reboot only when it is idle.The Reboot URL is: http:///admin/reboot3.4. Configuration Parameters3.4.1. System ParametersSystem ConfigurationParameter Name Description DefaultRestricted AccessDomainsThis feature is used when implementing softwarecustomization.Enable Web Server Enable/disable web server of SPAYesThis feature should only be used on firmware version 1.0.9 or later.Enable Web Admin Enable/disable Admin pages of web server of SPAYesAccessAdmin Password The password for administratorUser Password The password for UserNetwork ConfigurationParameter Name Description DefaultDHCP Enable/Disable DHCP YesHost Name Host Name of SPADomainThe network domain of SPAStatic IPStatic IP address of SPA, which will take effect if DHCP 0.0.0.0is disabledNetMask The NetMask used by SPA when DHCP is disabled 255.255.255.0GatewayThe default gateway used by SPA when DHCP is 0.0.0.0disabledPrimary DNS DNS server used by SPA in addition to DHCP supplied 0.0.0.0DNS servers if DHCP is enabled; when DHCP isdisabled, this will be the primary DNS server.Secondary DNS DNS server used by SPA in addition to DHCP suppliedDNS servers if DHCP is enabled; when DHCP isdisabled, this will be the secondary DNS server.0.0.0.0© 2003 - 2004 Sipura Technology, Inc Proprietary (See Copyright Notice on Page 2) 13
Page 7 and 8: The SPA has the following interface
Page 9 and 10: Note: This translation convention o
Page 11: Check SPA’s Web ServerPort170 Non
Page 15 and 16: Log Resync FailureMsgGPP A thru GPP
Page 17 and 18: SIT2 RSC 1SIT3 RSC 1SIT4 RSC 1Try B
Page 19 and 20: Ext IPExt RTP Port MinNAT Keep Aliv
Page 21 and 22: SIP 100REL EnableBlind Attn-XferEna
Page 23 and 24: The SPA provides native support of
Page 25 and 26: esources are available per SPA. The
Page 27 and 28: Parameter Name Description DefaultC
Page 29 and 30: Holding ToneConference ToneSecure C
Page 31 and 32: voltage is removed after the caller
Page 33 and 34: Feature Dial Services Codesprocesse
Page 35 and 36: GMT+02:00, …, GMT+13:00FXS Port I
Page 37 and 38: Hook StateRegistration StateLast Re
Page 39 and 40: would be highly undesirable especia
Page 41 and 42: The FXS interface is the same as th
Page 43 and 44: - VoIP1-to-VoIP2 and VoIP2-to-VoIP1
Page 45 and 46: set to “none” (and so the appl
Page 47 and 48: dialed-number is not specified or i
Page 49 and 50: switch (for US telcos, this value s
Page 51 and 52: is a SIP Re-INVITE request which th
Page 53 and 54: destination. This is Call Type #5 a
Page 55 and 56: [Line 1] = fwd.pulver.com[Line 1] =
Page 57 and 58: If Line 1 is busy when the PSTN lin
Page 59 and 60: - The and parameters still apply
Page 61 and 62: VoIP Caller IDPatternlink. Choose f
Page 63 and 64:
PSTN Access ListPSTN Caller 1 PINPS
Page 65 and 66:
Min CPC Durationdetection5. 6 segme
Page 67 and 68:
4.14.10. Line 1 - VoIP Fallback To
Page 69 and 70:
4.14.18. PSTN User - PSTN Ring Thru
Page 71 and 72:
This section of the Administration
Page 73 and 74:
User Action Required to Activate or
Page 75 and 76:
5.2.6. Call-Waiting with Caller IDS
Page 78 and 79:
Dial the number of the 3 rd party.W
Page 80 and 81:
not ring or provide call waiting wh
Page 82 and 83:
service is activated or deactivated
Page 84 and 85:
The SPA syntax for the dial plan cl
Page 86 and 87:
Interdigit Timer Master Override:Th
show all

Sipura SPA3000 User Guide - MyNetFone

Create successful ePaper yourself

Delete template?

Save as template?