Sipura SPA3000 User Guide - MyNetFone

More documents

Recommendations

Info

2. The configured dynamic payloads are used for outbound calls only where the SPA presents theSDP offer. For inbound calls with a SDP offer, SPA will follow the caller’s dynamic payload typeassignments3.4.4.2. SDP Audio Codec NamesParameter Name Description DefaultNSE Codec Name NSE Codec name used in SDP NSEAVT Codec Name AVT Codec name used in SDP telephone-eventG711a Codec Name G711a Codec name used in SDP PCMAG711u Codec Name G711u Codec name used in SDP PCMUG726r16 Codec Name G726-16 Codec name used in SDP G726-16G726r24 Codec Name G726-24 Codec name used in SDP G726-24G726r32 Codec Name G726-32 Codec name used in SDP G726-32G726r40 Codec Name G726-40 Codec name used in SDP G726-40G729a Codec Name G729a Codec name used in SDP G729aG729b Codec Name G729b Codec name used in SDP G729abG723 Codec Name G723 Codec name used in SDP G723Notes:1. SPA uses the configured codec names in its outbound SDP2. SPA ignores the codec names in incoming SDP for standard payload types (0 – 95).3. For dynamic payload types, SPA identifies the codec by the configured codec names. Comparisonis case-insensitive.3.4.4.3. NAT SupportParameter Name Description DefaultHandle_VIA_received If set to “yes”, the SPA will process the “received” Noparameter in the VIA header inserted by the serverin a response to any one of its request. Else theparameter is ignored.Handle_VIA_rport If set to “yes”, the SPA will process the “rport” Noparameter in the VIA header inserted by the serverin a response to any one of its request. Else theparameter is ignored.Insert VIA received Insert received parameter in VIA header in SIP Noresponses if received from IP and VIA sent-by IPdifferInsert VIA rport Insert rport parameter in VIA header in SIPNoresponses if received-from port and VIA sent-byport differSubstitute VIA addr Use nat-mapped IP:port values in VIA header NoSend Resp To Src Port Send response to the request source port instead of Nothe VIA sent-by portSTUN ServerSTUN server to contact for NAT mapping discoverySTUN Enable Enable the use of STUN to discover NAT mapping NoSTUN Test Enable If enabled with = “yes” and a valid, the SPA will perform a NAT typediscovery operation when first power on bycontacting the configured STUN server. The resultof the discovery will be reported in a WarningNo© 2003 - 2004 Sipura Technology, Inc Proprietary (See Copyright Notice on Page 2) 18
Ext IPExt RTP Port MinNAT Keep Alive Intvlheader in all subsequent REGISTER requests –“Warning: 399 spa ”, where is one of the following:"Unknown NAT Type","STUN Server Not Reachable","STUN Server Not Responding","Open Internet Detected","Symmetric Firewall Detected","Full Cone NAT Detected","Restricted Cone NAT Detected","Symmetric NAT Detected";If the SPA detects Symmetric Nat or SymmetricFirewall, Nat Mapping will be disabled (that is, nosubstitution of IP address and port with external IPaddress an nat-mapped port)External IP address to substitute for the actual IPaddress of the unit in all outgoing SIP messages. If“0.0.0.0” is specified, no IP address substitution isperformed.External port mapping of . If thisvalue is non-zero, the RTP port number in alloutgoing SIP messages is substituted by thecorresponding port value in the external RTP portrange.Interval between sending NAT-mapping keep alivemessage in sec0.0.0.0015Notes:3.4.5. Line 1 and Line 2 ParametersPer line parameter tags must be appended with [1] or [2] (corresponding to lines 1 or 2) in theconfiguration profile. It is omitted below for readability.3.4.5.1. User Account InformationParameter Name Description DefaultLine Enable Enable this line for service YesMOH Server 2 The User ID or URL of the auto-answering SAS to Emptycontact for MOH services. Examples: 5000,1001@music.sipura.com, 66.12.123.15:5061.Note: When only a user-id is given, the currentproxy or outbound proxy will be contacted as in themaking of a regular outbound call. MOH is disabledif this parameter is not specified (empty).SIP Port SIP message listening port and transmission port 5060Ext SIP PortExternal port to substitute for the actual SIP port of 0the unit in all outgoing SIP messages. If “0” isspecified, no SIP port substitution is performed.SIP TOS/DiffServ TOS/DiffServ field value in UDP IP Packets 0x68Valuecarrying a SIP MessageRTP TOS/DiffServValueTOS/DiffServ field value in UDP IP Packetscarrying a RTP data0xb8© 2003 - 2004 Sipura Technology, Inc Proprietary (See Copyright Notice on Page 2) 19
Page 7 and 8: The SPA has the following interface
Page 9 and 10: Note: This translation convention o
Page 11 and 12: Check SPA’s Web ServerPort170 Non
Page 13 and 14: http:///resync?[[protocol://][serve
Page 15 and 16: Log Resync FailureMsgGPP A thru GPP
Page 17: SIT2 RSC 1SIT3 RSC 1SIT4 RSC 1Try B
Page 21 and 22: SIP 100REL EnableBlind Attn-XferEna
Page 23 and 24: The SPA provides native support of
Page 25 and 26: esources are available per SPA. The
Page 27 and 28: Parameter Name Description DefaultC
Page 29 and 30: Holding ToneConference ToneSecure C
Page 31 and 32: voltage is removed after the caller
Page 33 and 34: Feature Dial Services Codesprocesse
Page 35 and 36: GMT+02:00, …, GMT+13:00FXS Port I
Page 37 and 38: Hook StateRegistration StateLast Re
Page 39 and 40: would be highly undesirable especia
Page 41 and 42: The FXS interface is the same as th
Page 43 and 44: - VoIP1-to-VoIP2 and VoIP2-to-VoIP1
Page 45 and 46: set to “none” (and so the appl
Page 47 and 48: dialed-number is not specified or i
Page 49 and 50: switch (for US telcos, this value s
Page 51 and 52: is a SIP Re-INVITE request which th
Page 53 and 54: destination. This is Call Type #5 a
Page 55 and 56: [Line 1] = fwd.pulver.com[Line 1] =
Page 57 and 58: If Line 1 is busy when the PSTN lin
Page 59 and 60: - The and parameters still apply
Page 61 and 62: VoIP Caller IDPatternlink. Choose f
Page 63 and 64: PSTN Access ListPSTN Caller 1 PINPS
Page 65 and 66: Min CPC Durationdetection5. 6 segme
Page 67 and 68: 4.14.10. Line 1 - VoIP Fallback To
Page 69 and 70:
4.14.18. PSTN User - PSTN Ring Thru
Page 71 and 72:
This section of the Administration
Page 73 and 74:
User Action Required to Activate or
Page 75 and 76:
5.2.6. Call-Waiting with Caller IDS
Page 78 and 79:
Dial the number of the 3 rd party.W
Page 80 and 81:
not ring or provide call waiting wh
Page 82 and 83:
service is activated or deactivated
Page 84 and 85:
The SPA syntax for the dial plan cl
Page 86 and 87:
Interdigit Timer Master Override:Th
show all

Sipura SPA3000 User Guide - MyNetFone

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?