HTI Manual - Desert Tactical Arms

More documents

Recommendations

Info

344. Once on paper, shoot a three shot group while aiming the cross hairs at the bullseye (fig 31).5. Use crosshairs subtended lines/dots to measure groups distance from bulls eye.You can also measure the distance from bulls eye using a tape-measure, howeveryou will need the conversion formulas (page 36) to change from inches to MOAor MILS. Adjust as per measurements and shoot another 3 shots while aiming atbulls eye (fig. 32).Example: Down 1.6 MilsLeft 1.1 MilsFigure 31 Figure 326. Repeat step 5 until you are satisfied. Note, a rifle shoots at an area not at a singlepoint, so ensure that the center of the group is where your zero is.
SCOPE TURRETS VALUEThe two most common scope adjustment values are Minutes of Angle (MOA) and MilRadians (MILS).1. 1 MOA = 1.047” @ 100 yards2. 1 MIL = 3.6” @ 100 yards3. 1 MIL = 3.438 MOA4. 1 MOA = 0.29 MILSIf you think in terms of inches you must realize that MOA values and MIL valuesare angular measurements, which means that the inch value of both MOA and MILincreases with distance (see illustration below).1 MOA1 MIL100 yds 200 yds 300 yds100 yds 200 yds 300 yds35
Page 3 and 4: For video instructions see our webs
Page 5 and 6: CARE AND CLEANING..................
Page 7 and 8: Before shooting the rifle:• Alway
Page 9 and 10: SIGHTSPicatinny rail (no taper)BARR
Page 11 and 12: CompactRuggedThe HTI’s bullpup de
Page 13 and 14: Other Benefits• The full length M
Page 15 and 16: DISASSEMBLY AND ASSEMBLY1. This cha
Page 17 and 18: REMOVING BARREL1. Remove buttpad an
Page 19 and 20: 3. Make sure the barrel is fully se
Page 22 and 23: 6. Ease the spring and follower out
Page 24 and 25: REMOVING STOCK PANELS221. Place the
Page 26 and 27: LOADING AND UNLOADINGINSERTING THE
Page 28 and 29: UNLOADING (CLEARING) THE HTI1. Plac
Page 30 and 31: ADJUSTING CHEEK PIECE1. With an 5mm
Page 32 and 33: 6. Install ring tops.7. Finger tigh
Page 34 and 35: QUICK ZEROING1. Find the center of
Page 38 and 39: It is easier to train yourself to s
Page 40 and 41: INITIAL CLEANING1. Upon receipt of
Page 42 and 43: • Allow to sit for 15 minutes.•
Page 44 and 45: BEFORE AND AFTER FIRINGCLEANING BEF
Page 46 and 47: ADDITIONAL DISASSEMBLY & AS-SEMBLYB
Page 48 and 49: BOLT ASSEMBLY1. Insert the firing p
Page 50 and 51: 5. Hold the bolt with the end cap f
Page 52 and 53: 2. MAGAZINE NOT EMPTY (Malfunction)
Page 54 and 55: B. FAILURE TO CHAMBER * Bolt does n
Page 56 and 57: 4. Fouled Extractor5. Extractor Def
Page 58 and 59: PARTS EXPLODED VIEWHTI56BarrelBoltR
Page 60 and 61: MAGAZINE58Floor PlateFollowerMagazi
Page 62 and 63: PATENTS PENDINGNo part of this docu

HTI Manual - Desert Tactical Arms

Create successful ePaper yourself

Delete template?

Save as template?