HTI Manual - Desert Tactical Arms

More documents

Recommendations

Info

B. FAILURE TO CHAMBER * Bolt does not fully close and rifle will notfire.52CAUSE1. Incorrect Cocking2. Dirty Chamber3. Defective Ammunition4. Very dirty rifleREMEDYRemove magazine. Re run the bolt and reload.Clean.Check for damaged cartridges.Check to see if the bolt and firing mechanism issluggish. Clean and oil if necessary.C. FAILURE TO FIRE * Striker assembly snaps home but rifle willnot fire.CAUSE1. Bolt not Fully Closed2. Defective CartridgeREMEDYFollow procedure for incorrect cocking or shortrecoil.Inspect primer. If fully indented discard safely.If not fully indented, check firing mechanism.
3. Dirty Firing Mechanism Check to see if operaion is sluggish.4.5.6.Defective Firing PinDefective Striker AssemblyBarrel Not Properly SeatedClean and replace as necessary.Clean and replace as necessary.Make sure the locating notch on the barrelextension lines up with the feed ramp of thereceiver and is fully seated (see pages 16-18).D. FAILURE TO EXTRACT OREJECTCAUSE1. Overpowered Ammunition(Stuck Case)2. Dirty or Damaged ChamberThe fired case may not eject, or the riflemay jam (spent case left in chamber).REMEDYCheck ammunition and change to a differentbrand of currently commercially manufacturedammunition if problem persists.Inspect, clean, replace barrel if necessary.3. Defective Ammunition Check ammunition for damage. Replace ifproblem persists.53
Page 3 and 4: For video instructions see our webs
Page 5 and 6: CARE AND CLEANING..................
Page 7 and 8: Before shooting the rifle:• Alway
Page 9 and 10: SIGHTSPicatinny rail (no taper)BARR
Page 11 and 12: CompactRuggedThe HTI’s bullpup de
Page 13 and 14: Other Benefits• The full length M
Page 15 and 16: DISASSEMBLY AND ASSEMBLY1. This cha
Page 17 and 18: REMOVING BARREL1. Remove buttpad an
Page 19 and 20: 3. Make sure the barrel is fully se
Page 22 and 23: 6. Ease the spring and follower out
Page 24 and 25: REMOVING STOCK PANELS221. Place the
Page 26 and 27: LOADING AND UNLOADINGINSERTING THE
Page 28 and 29: UNLOADING (CLEARING) THE HTI1. Plac
Page 30 and 31: ADJUSTING CHEEK PIECE1. With an 5mm
Page 32 and 33: 6. Install ring tops.7. Finger tigh
Page 34 and 35: QUICK ZEROING1. Find the center of
Page 36 and 37: 344. Once on paper, shoot a three s
Page 38 and 39: It is easier to train yourself to s
Page 40 and 41: INITIAL CLEANING1. Upon receipt of
Page 42 and 43: • Allow to sit for 15 minutes.•
Page 44 and 45: BEFORE AND AFTER FIRINGCLEANING BEF
Page 46 and 47: ADDITIONAL DISASSEMBLY & AS-SEMBLYB
Page 48 and 49: BOLT ASSEMBLY1. Insert the firing p
Page 50 and 51: 5. Hold the bolt with the end cap f
Page 52 and 53: 2. MAGAZINE NOT EMPTY (Malfunction)
Page 56 and 57: 4. Fouled Extractor5. Extractor Def
Page 58 and 59: PARTS EXPLODED VIEWHTI56BarrelBoltR
Page 60 and 61: MAGAZINE58Floor PlateFollowerMagazi
Page 62 and 63: PATENTS PENDINGNo part of this docu

HTI Manual - Desert Tactical Arms

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?