Installation Manual HLF-25, 30, 40, & 50 - Waltco

More documents

Recommendations

Info

Chapter 4Roller Bracket Adjustment: (For bed heights above52” and all walk ramp applications)Verify roller bracket is in correct orientation for bedheight of vehicle and walk ramp application.If needed, remove all (3) three bolts to re-orientate theroller bracket as show for correct application.NOTE: Platform must lean towards parting barbetween 2 and 18 degrees.IMPORTANT:Improper installation of parting bar can result indamage to the liftgate platform, by powering into thechassis frame of vehicle.WELD PARTING BAR AFTER FUNCTIONALITY ISCONFIRMED. ¼” WELD 100%Installation23"25 3 4 "For Bed Heights of 52” or lowerFor Bed Heights above 52”Also used if vehicle has a walk rampGR02800PARTING BAR 2:To assist the opening of the platform:Vehicles without walk ramp:Lower platform to ground with slight tilt towards vehicleas shown. Slide parting bar to platform and bolt intoplace.Vehicles with walk ramp:Locate parting bar in hole closest to mount tube and boltinto place.Tighten nuts and bolts to 50 ft lbs.Platform is to lean in towards parting barwhen at ground. It is not to fall open toground.Parting BarWalk Ramp Position2 to 18degreeleanGR02900Page 26
Chapter 4ADJUST PLATFORM TILTAdjust bolts between Stop Block and Platform Hingeto achieve 1” - 2” tilt up of platform as shown. Agreater tilt up is recommended for higher capacities.Installation1” - 2”NOTE:Adjust both Stop Block Bolts evenly.Tighten Jam Nuts.Jam NutAdjustmentBoltGR02668, GR02690Page 27
Page 1 and 2: www.waltco.com Phone: 800.411.5685p
Page 3 and 4: IntroductionIf anyone observes impr
Page 5 and 6: Liftgates with Tilt Function• Pro
Page 7 and 8: Chapter 2Liftgate Terminology19. Mo
Page 9 and 10: Chapter 3 Determine Basic Mounting
Page 11 and 12: Chapter 4InstallationCut away vehic
Page 13 and 14: Chapter 4InstallationALTERNATIVE WE
Page 15 and 16: Chapter 4InstallationBolts heads sh
Page 17 and 18: Chapter 4OPTIONAL INSTALLATIONIf th
Page 19 and 20: Chapter 4InstallationRoute control
Page 21 and 22: Chapter 4INSTALLATION OF POWER CABL
Page 23 and 24: Chapter 4REMOVE MOUNTING BAR, WEDGE
Page 25: Chapter 4There is no speed adjustme
Page 29 and 30: Chapter 4Waltco offers three sugges
Page 31 and 32: Chapter 4STEP ADJUSTMENTInstallatio
Page 33 and 34: Chapter 5Placement of DecalsAll dec
Page 35 and 36: Chapter 7 FINAL INSPECTION SHEETIMP
Page 37 and 38: Hand Held Remote InstallationLPF Li
Page 39 and 40: Auxiliary Battery Kit w/Dual Cables
Page 45 and 46: Installation of Cab Shut Off Switch
Page 47 and 48: HLF WALK RAMP KITINSTALLATION INSTR
Page 49 and 50: HLF WALK RAMP KITINSTALLATION INSTR
Page 51 and 52: Chapter 8How To Order PartsRepairs
Page 53 and 54: Every vehicle that has a WALTCO Lif

Installation Manual HLF-25, 30, 40, & 50 - Waltco

Create successful ePaper yourself

Delete template?

Save as template?