Installation Manual HLF-25, 30, 40, & 50 - Waltco

More documents

Recommendations

Info

Chapter 4INSTALL BRACESInstallationBolt brace and support angles as shown.Support angle to span a minimum of 3 or 4crossmembers.Note:It may be necessary to trim rearward end of supportangles to clear rear sill and/or dock bumper.Weld support angles to all crossmembers it contactswith minimum four (4) inches of 1/8” weld.Support Angle *Brace Angle *GR02921After installation of dock bumpers, ground clearance needs to be considered. If dock bumper steps are too low,they may hit the ground when driving in or out of driveways, etc.Adjust dock bumper steps to achieve recommended ground clearance of 20” – 24” as shown below.Note: Overhangs greater than 11 feet may need dock bumper steps set higher to maintain a 10º departure angle.Use formula below to calculate ground clearance.Bed heights below 46” may require the lower step to be completely removed to achieve sufficient groundclearance.Ground Clearance20" - 24"Calculate Ground Clearance for 10ºdeparture angle:Ground Clearance = Overhang x .176OVERHANG (inches)GR02896Page 30
Chapter 4STEP ADJUSTMENTInstallationSteps for non-light dock bumpers can be lowered bysimply unbolting and lowering to desired setting.For dock bumpers with lights, it will be necessary toinstall steps.1. Determine correct step height per aboverecommendations.2. Identify hole set required for bolting intoposition.3. Cut off step legs just above hole set required.4. Bolt into position as shown.Torque bolts to 34-37 ft. lbs.Cut both legs justabove holes to beused for boltingGR02744Page 31
Page 1 and 2: www.waltco.com Phone: 800.411.5685p
Page 3 and 4: IntroductionIf anyone observes impr
Page 5 and 6: Liftgates with Tilt Function• Pro
Page 7 and 8: Chapter 2Liftgate Terminology19. Mo
Page 9 and 10: Chapter 3 Determine Basic Mounting
Page 11 and 12: Chapter 4InstallationCut away vehic
Page 13 and 14: Chapter 4InstallationALTERNATIVE WE
Page 15 and 16: Chapter 4InstallationBolts heads sh
Page 17 and 18: Chapter 4OPTIONAL INSTALLATIONIf th
Page 19 and 20: Chapter 4InstallationRoute control
Page 21 and 22: Chapter 4INSTALLATION OF POWER CABL
Page 23 and 24: Chapter 4REMOVE MOUNTING BAR, WEDGE
Page 25 and 26: Chapter 4There is no speed adjustme
Page 27 and 28: Chapter 4ADJUST PLATFORM TILTAdjust
Page 29: Chapter 4Waltco offers three sugges
Page 33 and 34: Chapter 5Placement of DecalsAll dec
Page 35 and 36: Chapter 7 FINAL INSPECTION SHEETIMP
Page 37 and 38: Hand Held Remote InstallationLPF Li
Page 39 and 40: Auxiliary Battery Kit w/Dual Cables
Page 45 and 46: Installation of Cab Shut Off Switch
Page 47 and 48: HLF WALK RAMP KITINSTALLATION INSTR
Page 49 and 50: HLF WALK RAMP KITINSTALLATION INSTR
Page 51 and 52: Chapter 8How To Order PartsRepairs
Page 53 and 54: Every vehicle that has a WALTCO Lif

Installation Manual HLF-25, 30, 40, & 50 - Waltco

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?