DigiTrace NGC-UIT Loader Utility - Pentair Thermal Management

More documents

Recommendations

Info

Table of ContentsSection 1 Introduction ....................................................................................................................................... 31.1 Welcome ................................................................................................................................................ 31.2 User Responsibilities ......................................................................................................................... 31.3 Safety Warnings .................................................................................................................................. 31.4 License Agreement ............................................................................................................................ 31.5 Technical Support ............................................................................................................................... 71.6 System Requirements ....................................................................................................................... 7Section 2 DigiTrace NGC-UIT Parameter Upload and Download Utility ...................................... 72.1 Excel Spreadsheet – Circuit Configuration Data ...................................................................... 82.2 Importing XML Files into the NGC-UIT ...................................................................................... 122.3 Backup the NGC-30 UIT Database .............................................................................................. 202.4 Exporting XML Files from the 200N Controller ....................................................................... 28Appendix 1. Connecting an NGC-UIT to a Computer Using an Ethernet Connection ..... 31Appendix 2. Procedure to Release COM ports used by DTS ..................................................... 33Description ................................................................................................................................................. 33Procedures ................................................................................................................................................ 33THERMAL MANAGEMENT SOLUTIONS EN-NGC30LoaderUtility-IM-H58045 04/13 2/34
Section 1 Introduction1.1 WelcomeThis manual provides instructions for use of parameter upload and download forDigiTrace NGC-30 Heat-Tracing Control and Monitoring System. The parameter uploadutility simplifies the configuration of multiple circuits by providing the ability to massupload the configuration data into the DigiTrace NGC User Interface Terminal.1.2 User ResponsibilitiesThe performance, reliability and safety of your heat-tracing system depend on properdesign, selection and installation. The DigiTrace NGC-UIT Loader Utility will help youconfigure and update DigiTrace NGC-30 Heat-Tracing Control and Monitoring System,but it is only a tool. It assumes that your input is accurate, that you are familiar withheat-tracing system design and configuration, and that you will ensure that the uploadedconfiguration of the heat-tracing system is installed, maintained and used as intended.The DigiTrace NGC-UIT Loader Utility should be used under supervision of aknowledgeable engineer to ensure it is used appropriately.1.3 Safety WarningsThere are important safety warnings shipped with our products and printed in ourliterature. Be sure to read and follow them to reduce the risk of fire, shock or personalinjury. If you have any questions, contact your local representative or Pentair ThermalManagement directly.1.4 License AgreementPentair Thermal Management, LLCUser Interface Terminal (UIT) Loader Program Software License AgreementPLEASE REVIEW THE FOLLOWING TERMS AND CONDITIONS OF THIS SOFTWARELICENSE AGREEMENT (THE "AGREEMENT") CAREFULLY. THIS IS A LEGAL AGREEMENTBETWEEN YOU, THE END USER, AND PENTAIR THERMAL MANAGEMENT, LLC("PENTAIR THERMAL MANAGEMENT"). THE TERMS OF THIS AGREEMENT GOVERNYOUR USE OF THE DIGITRACE NGC-UIT LOADER UTILITY, AND ANY ACCOMPANYINGWRITTEN MATERIALS OR FILES. BY INSTALLING, ACCESSING, OR OTHERWISE USINGTHE SOFTWARE, YOU ACKNOWLEDGE THAT YOU HAVE READ AND UNDERSTOOD ALLOF THE TERMS AND CONDITIONS OF THE AGREEMENT AND ARE AGREEING TO BEBOUND BY THE TERMS OF THIS AGREEMENT.IF YOU DO NOT ACCEPT ALL OF THE TERMS AND CONDITIONS OF THIS AGREEMENT,DO NOT INSTALL, ACCESS, OR USE THE SOFTWARE. IF YOU ACQUIRED THE SOFTWAREON TANGIBLE MEDIA (E.G., CD-ROM) WITHOUT AN OPPORTUNITY TO REVIEW THISAGREEMENT AND YOU DO NOT ACCEPT THIS AGREEMENT, (1) DO NOT INSTALL OR USETHE SOFTWARE; AND (2) DESTROY OR RETURN THE SOFTWARE AND ALL OTHER ITEMSRECEIVED WITH THE DISK (INCLUDING WRITTEN MATERIALS, PACKAGING, ETC.) TOTHE PLACE WHERE YOU OBTAINED THEM, WITHIN THIRTY (30) DAYS OF RECEIPT. THISSOFTWARE IS BEING PROVIDED FREE OF CHARGE AT THE DISCRETION OF PENTAIRTHERMAL MANAGEMENT.THERMAL MANAGEMENT SOLUTIONS EN-NGC30LoaderUtility-IM-H58045 04/13 3/34
Page 1: 平成 24 年 9 月 21 日京都
Page 5 and 6: MEET YOUR REQUIREMENTS, OR THAT THE
Page 7 and 8: 1.5 Technical SupportFor technical
Page 9 and 10: Step 3Once you have entered all the
Page 11 and 12: A dialogue box will open to select
Page 13 and 14: Step 2B (For UIT Software version 1
Page 15 and 16: 2.2.2 Importing the .XML configurat
Page 17 and 18: equired to make the connection to t
Page 19 and 20: Step 1Connect a laptop computer to
Page 21 and 22: If a version of the NGC-30 UIT Soft
Page 23 and 24: as ºF, when the circuit data is im
Page 25 and 26: Click on the Save Data button (Labe
Page 27 and 28: Select the file that should be impo
Page 29 and 30: Step 3Click on the Save to XML File
Page 31 and 32: Appendix 1. Connecting an NGC-UIT t
Page 33 and 34: Appendix 2. Procedure to Release CO

DigiTrace NGC-UIT Loader Utility - Pentair Thermal Management

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?