AGP Pellet Stove - Avalon

More documents

Recommendations

Info

14 Installation (For Qualified Installers Only)Alcove Installation RequirementsWhen the pellet stove is placed in a location where the ceiling height is less than 7' (2.134 M) tall, it isconsidered an alcove installation. Because of the reduced height, the requirements listed below must bemet.• Minimum height is 60"• Minimum width is 36-9/16"• Maximum depth is 48"Restrictor Adjustment• Minimum clearance of 6" on each side and 3" on back• Minimum clearance of 3” for horizontal venting• Minimum clearance of 2” from pipe for vertical ventingFor installations with a tall flue, the restrictor may be needed to adjust airflow to the fire platform. Thiskeeps the fire platform and glass as clean as possible.For low heat output settings the restrictor may need to be closed or near closed to limit the amount ofair. This prevents the stove from burning the pellet fuel faster than it is fed.For medium heat output settings the restrictor may need to be opened to a medium position.For high heat output settings the restrictor will need to be opened to a high position. This prevents thefire platform from over-filling with pellets and becoming clogged with ash clumps.Keeping your fire platform clean is the most important step to maintaining a safe and efficient stove.Check and clean your fire platform daily until you find the correct restrictor settings and appropriate fireplatform cleaning interval.Not Enough AirIf clinkers (ashes that solidify into a clump)develop or the flame appears lazy and slowto blow the ash out of the fire platform,push the restrictor in until the flamebecomes active and the fire platform holesremain clean.NOTE: If the restrictor is fully in, yet the fireplatform does not remain clean, the stoveneeds to be cleaned and checked for airleaks (see “Maintenance” section of thismanual).Too Much AirIf the flames are too active (small, flickeringflames), move the restrictor rod out untilthe flame slows down.NOTE: It is acceptable to have “glowingembers” jump out of the fire platform.Another symptom of too much air is theheater “blowing the fire out” – a condition inwhich the pellets burn faster than they arefed (this is most common on low heatsettings).More AirLess Air© Travis Industries 4130924 100-01330_004
Installation (For Qualified Installers Only) 15Installation ExamplesInstallation Example: Direct "Through-the-wall" InstallationHorizontal Rain Cap12” MinimumType "L" VentHouse Shield (used to protectexterior wall from sootdiscoloration) is HIGHLYRECOMMENDEDWall Thimble(note clearancebetween vent andcombustibles)3” Minimum6” Minimum6” MinimumFloor Protection500° F. RTVSiliconeSeal each ventsection (includingadapters, elbows,etc...) by injecting aliberal amount of500° F. RTVsilicone into the gapbetween sections,unless otherwisespecified by themanufacturer.3” Minimum12”MinimumFloor ProtectionNOTE: Travis Industries recommends a minimum vertical vent of 5’ to ensure adequate draft during apower outage.Install the vent at the clearance specified by the vent manufacturer.© Travis Industries 4130924 100-01330_004
Page 4: 4 Safety PrecautionsHOT WHILE IN OP
Page 7 and 8: Installation (For Qualified Install
Page 13: Installation (For Qualified Install
Page 21 and 22: Safety NoticeOperation 21READ THIS
Page 23 and 24: Operation 23Manual ModeManual mode
Page 25 and 26: TSTAT (Thermostat) ModeOperation 25
Page 27 and 28: Operation 27Start-Up Sequence (Igni
Page 29 and 30: Stove Maintenance ToolsMaintenance
Page 31 and 32: Maintenance 31b) Slide the the visu
Page 33 and 34: Maintenance 33Weekly Maintenance (o
Page 35 and 36: Maintenance 354. Remove the rear li
Page 37 and 38: Maintenance 37Yearly Maintenance (o
Page 43 and 44: Maintenance 43Wiring Diagram6 - Pin
Page 45 and 46: Optional Equipment 454. Route the w
Page 47 and 48: Optional Equipment 4713. Connect th
Page 49 and 50: Limited 7 Year Warranty 49To regist

AGP Pellet Stove - Avalon

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?