System configuration - Lantech Communications Global Inc

More documents

Recommendations

Info

Bottom ViewThe bottom panel of the 6 10/100/1000T + 2 10/100/1000T/Dual Speed SFP Combo w/Pro-Ring Managed Industrial Switch has one terminal block connector in which has twoDC power inputs.Bottom Panel of the industrial switchLED IndicatorsThere are diagnostic LED indicators located on the front panel of the industrial switch.They provide real-time information of system and optional status. The following tableprovides description of the LED status and their meanings for the switch.LED Status DescriptionPWRR.M.GreenOffGreen<strong>System</strong> power onNo power inputThe industrial switch is the master of the X-Ring group5
PWR1PWR2FaultLNK/ACT(for P7, P8 SFP)P1 ~ P8 (RJ-45)OffGreenOffGreenOffRedOffGreenBlinkingOffGreen(upper LED)Blinking(upper LED)Off(lower LED)Green(lower LED)Off(lower LED)The industrial switch is not the ring master inthe X-Ring groupPower input 1 is activePower input 1 is inactivePower input 2 is activePower input 2 is inactivePower input 1 or 2 is inactive or port linkfailure (depends on Fault Relay Alarm<strong>configuration</strong>)Power input 1 and 2 are both active, or nopower inputsSFP port is linkingData is transmitting or receivingNot connected to networkConnected to networkNetworking is activeNo connected to networkThe port is operating at speed of 1000MThe port is disconnected or working at speedof 10/100M6
Page 5 and 6: Login in the Console Interface ....
Page 7 and 8: SNMP Configuration ................
Page 9 and 10: ‣ Port Base, Tag Base and Type of
Page 11: Hardware DescriptionIn this paragra
Page 15 and 16: Straight Through Cable SchematicCro
Page 17 and 18: Second, insert the fiber cable of L
Page 19 and 20: Cabling• Using four twisted-pair,
Page 21 and 22: Insert the wires into the fault ala
Page 23 and 24: 1. First, insert the top of DIN-Rai
Page 25 and 26: Hardware InstallationIn this paragr
Page 27 and 28: X-Ring ApplicationThe industrial sw
Page 29 and 30: X-Ring IRecovery time tableRecovery
Page 31 and 32: Login in the Console InterfaceWhen
Page 33 and 34: The following table lists the CLI c
Page 35 and 36: [System Location] location string x
Page 37 and 38: HTTP serverno security telnet G Dis
Page 39 and 40: andwidth control fastEthernet 2swit
Page 41 and 42: VLAN Commands SetCommands Level Des
Page 43 and 44: [0~61440] tree priority parameter p
Page 45 and 46: Autostp-admin-edge[True|False]I Adm
Page 47 and 48: static address table staticshow mac
Page 49 and 50: configurationno snmp community-GRem
Page 51 and 52: 8021x systemaccountport[port ID]802
Page 53 and 54: estoreflash:restore_cfgupgradeflash
Page 55 and 56: no event smpt I Disable port event
Page 57 and 58: coupleringno Xring dualhoming G Dis
Page 59 and 60: System Login1. Launch the Internet
Page 61 and 62: System InformationAssign the system
Page 63 and 64:
dynamic IP assigns range. For examp
Page 65 and 66:
Update Firmware interfaceTFTP - Res
Page 67 and 68:
Syslog Configuration interfaceSyste
Page 69 and 70:
• System event selection: 4 selec
Page 71 and 72:
Fault Relay Alarm interfaceSNTP Con
Page 73 and 74:
CCT - China Coast,USSR Zone 7JST -
Page 75 and 76:
IP Security interfaceUser Authentic
Page 77 and 78:
Port Statistics interfacePort Contr
Page 79 and 80:
2. Group ID: There are three trunk
Page 81 and 82:
State ActivityWhen you have setup t
Page 83 and 84:
Rate Limiting interface• All the
Page 85 and 86:
VLAN - Port Based interface• Clic
Page 87 and 88:
802.1Q VLANTag-based VLAN is an IEE
Page 89 and 90:
Group Configuration interface3. You
Page 91 and 92:
RSTP System Configuration interface
Page 93 and 94:
problems by receiving traps or chan
Page 95 and 96:
Trap Managers interfaceSNMPV3 Confi
Page 97 and 98:
Group TableConfigure SNMP v3 group
Page 99 and 100:
QoS Configuration interface92
Page 101 and 102:
that support IGMP. Enabling IGMP al
Page 103 and 104:
The system also supports the Coupli
Page 105 and 106:
• SecurityIn this section, you ca
Page 107 and 108:
802.1x Per Port Setting interfaceMi
Page 109 and 110:
Static MAC Addresses interfaceMAC F
Page 111 and 112:
Factory DefaultReset switch to defa
Page 113 and 114:
Troubles shooting• Verify that is
Page 115 and 116:
Packet Buffer1MbitsMAC address8K MA
Page 117 and 118:
Port Trunk withLACPClass of service
show all

System configuration - Lantech Communications Global Inc

Create successful ePaper yourself

Delete template?

Save as template?