System configuration - Lantech Communications Global Inc

More documents

Recommendations

Info

Network ApplicationThis chapter provides some sample applications to help user to have more actual idea ofindustrial switch function application. A sample application of the industrial switch isshown as below:19
X-Ring ApplicationThe industrial switch supports the X-Ring protocol that can help the network system torecovery from network connection failure within 300ms or less, and make the networksystem more reliable. The X-Ring algorithm is similar to Spanning Tree Protocol(STP)/RSTP algorithm but its recovery time is less than STP/RSTP. The following figureis a sample of X-Ring application.20
Page 5 and 6: Login in the Console Interface ....
Page 7 and 8: SNMP Configuration ................
Page 9 and 10: ‣ Port Base, Tag Base and Type of
Page 11 and 12: Hardware DescriptionIn this paragra
Page 13 and 14: PWR1PWR2FaultLNK/ACT(for P7, P8 SFP
Page 15 and 16: Straight Through Cable SchematicCro
Page 17 and 18: Second, insert the fiber cable of L
Page 19 and 20: Cabling• Using four twisted-pair,
Page 21 and 22: Insert the wires into the fault ala
Page 23 and 24: 1. First, insert the top of DIN-Rai
Page 25: Hardware InstallationIn this paragr
Page 29 and 30: X-Ring IRecovery time tableRecovery
Page 31 and 32: Login in the Console InterfaceWhen
Page 33 and 34: The following table lists the CLI c
Page 35 and 36: [System Location] location string x
Page 37 and 38: HTTP serverno security telnet G Dis
Page 39 and 40: andwidth control fastEthernet 2swit
Page 41 and 42: VLAN Commands SetCommands Level Des
Page 43 and 44: [0~61440] tree priority parameter p
Page 45 and 46: Autostp-admin-edge[True|False]I Adm
Page 47 and 48: static address table staticshow mac
Page 49 and 50: configurationno snmp community-GRem
Page 51 and 52: 8021x systemaccountport[port ID]802
Page 53 and 54: estoreflash:restore_cfgupgradeflash
Page 55 and 56: no event smpt I Disable port event
Page 57 and 58: coupleringno Xring dualhoming G Dis
Page 59 and 60: System Login1. Launch the Internet
Page 61 and 62: System InformationAssign the system
Page 63 and 64: dynamic IP assigns range. For examp
Page 65 and 66: Update Firmware interfaceTFTP - Res
Page 67 and 68: Syslog Configuration interfaceSyste
Page 69 and 70: • System event selection: 4 selec
Page 71 and 72: Fault Relay Alarm interfaceSNTP Con
Page 73 and 74: CCT - China Coast,USSR Zone 7JST -
Page 75 and 76: IP Security interfaceUser Authentic
Page 77 and 78:
Port Statistics interfacePort Contr
Page 79 and 80:
2. Group ID: There are three trunk
Page 81 and 82:
State ActivityWhen you have setup t
Page 83 and 84:
Rate Limiting interface• All the
Page 85 and 86:
VLAN - Port Based interface• Clic
Page 87 and 88:
802.1Q VLANTag-based VLAN is an IEE
Page 89 and 90:
Group Configuration interface3. You
Page 91 and 92:
RSTP System Configuration interface
Page 93 and 94:
problems by receiving traps or chan
Page 95 and 96:
Trap Managers interfaceSNMPV3 Confi
Page 97 and 98:
Group TableConfigure SNMP v3 group
Page 99 and 100:
QoS Configuration interface92
Page 101 and 102:
that support IGMP. Enabling IGMP al
Page 103 and 104:
The system also supports the Coupli
Page 105 and 106:
• SecurityIn this section, you ca
Page 107 and 108:
802.1x Per Port Setting interfaceMi
Page 109 and 110:
Static MAC Addresses interfaceMAC F
Page 111 and 112:
Factory DefaultReset switch to defa
Page 113 and 114:
Troubles shooting• Verify that is
Page 115 and 116:
Packet Buffer1MbitsMAC address8K MA
Page 117 and 118:
Port Trunk withLACPClass of service
show all

System configuration - Lantech Communications Global Inc

Create successful ePaper yourself

Delete template?

Save as template?