EIS-2 & EIS-2-RJ - iServer Industrial MicroServer Manual - NEWPORT

More documents

Recommendations

Info

2.5 Network Communication Interfaces2.5.1 10Base-T RJ-45 PinoutThe 10BASE-T Ethernet network (RJ-45) system is used in the iServer for networkconnectivity. The 10 Mbps twisted-pair Ethernet system operates over two pairs of wires.One pair is used for receiving data signals and the other pair is used for transmitting datasignals. This means that four pins of the eight-pin connector are used.Pin Name Description1 +Tx + Transmit Data2 -Tx - Transmit Data3 +RX + Receive Data4 N/C Not Connected5 N/C Not Connected6 -Rx - Receive Data7 N/C Not Connected8 N/C Not Connected2.5.2 10Base-T Crossover WiringFigure 2.6 RJ45 PinoutWhen connecting the iServer directly to the computer, the transmit data pins of thecomputer should be wired to the receive data pins of the iServer, and vice versa. The10Base-T crossover cable with pin connection assignments are shown on Figure 2.7.Figure 2.7 10Base-T Crossover Cable WiringUse straight through cable for connecting the iServer to an Ethernet hub.The ports on the hub are already crossed.8
PART 3NETWORK CONFIGURATION3.1 Network ProtocolsThe iServer can be connected to the network using standard TCP/IP protocols.It also supports ARP, HTTP (WEB server), DHCP, DNS, and Telnet protocols.3.2 Ethernet (MAC) AddressMAC (Media Access Control) address is your computer's unique hardware number.When you're connected to the LAN from your computer, a correspondence table relatesyour IP address to your computer's physical (MAC) address. The MAC address can befound on the label of your device and contains 6 bytes (12 characters) of hexadecimalnumbers XX:XX:XX:XX:XX:XX hexFor example: 0A:0C:3D:0B:0A:0BThere is room on the label to put your IP address. See Figure 3.1.MODEL/SERIAL LABELMODEL NO: EIS-2SERIAL NO:INPUT POWER:IP:MAC00:00:00:00:00:00BLANK FORCUSTONER'SIP ADDRESSFigure 3.1 LabelingMAC ADDRESSLABEL INHEX CODE9
Page 1 and 2: Industrial MicroServerEIS-2 and EIS
Page 3 and 4: TABLE OF CONTENTSPart 1: Introducti
Page 5 and 6: NOTES, WARNINGS and CAUTIONSInforma
Page 7 and 8: RX TX ON COL1.3 DescriptionThis dev
Page 9 and 10: 2.3 Parts of the iServer UnitTX RX
Page 11: 2.4.2 Wiring RS485 InterfaceRS485 i
Page 15 and 16: 3.5 IP AddressEvery active device c
Page 17 and 18: 4.1 Setup and Operation Using the i
Page 19 and 20: 4.1.3 Modify Device List Entry• U
Page 21 and 22: Timeout: The amount of time that th
Page 23 and 24: 4.2 Setting a New IP Address using
Page 25 and 26: 4.3 Setting a New IP Address over t
Page 27 and 28: 4.5 Telnet SetupTelnet stands for T
Page 29 and 30: 4.6 HTTPGET ProgramYou can setup an
Page 31 and 32: 4.8 Remote Access (Tunneling)To "tu
Page 33 and 34: 4.8.2 Local iServer1. An IP address
Page 35 and 36: 4.9.2 Program Options Setup and Con
Page 37 and 38: PART 5SPECIFICATIONSSERIAL INTERFAC
Page 39 and 40: APPENDIX AGLOSSARYUser of this manu
Page 41 and 42: Appendix CIP NetmaskIP Netmask or S
Page 43 and 44: Appendix DASCII Chart Continuation/
Page 47 and 48: Warranty/DisclaimerNEWPORT Electron

EIS-2 & EIS-2-RJ - iServer Industrial MicroServer Manual - NEWPORT

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?