EIS-2 & EIS-2-RJ - iServer Industrial MicroServer Manual - NEWPORT

More documents

Recommendations

Info

PART 6FACTORY PRESET VALUESPRESET PARAMETERSFACTORY DEFAULTSNetwork Interface:IP Address 128.100.101.254Gateway Address 0.0.0.0Subnet Mask 255.255.0.0Device Host Nameeis and the last 4 digits from the MAC addressLogin Password 12345678Admin Password 00000000DHCPDisabledSerial Interface:Communication ProtocolRS-232Flow ControlNoneBaud Rate 9600ParityNoneStop Bit1 bitData Bit8 bitsTimeout500 msecEnd Character0D (Hex) (Carridge Return)Terminal Server:Server TypeSlaveNumber of Sockets 0Port # 2000Server ModeDisableRemote Access (Tunneling):Remote AccessDisableRemote Port 2000Remote IP Address 0.0.0.034
APPENDIX AGLOSSARYUser of this manual should be familiar with following definitions:ARP (Address Resolution Protocol) is a protocol for mapping an Internet Protocoladdress (IP address) to a physical machine address that is recognized in the localnetwork. For example, the IP address in use today is an address that is 32-bits long.In an Ethernet local area network, however, addresses for attached devices are 48-bitslong. (The physical machine address is also known as a Media Access Control orMAC address.) A table, usually called the ARP cache, is used to maintain a correlationbetween each MAC address and its corresponding IP address. ARP provides theprotocol rules for making this correlation and providing address conversion in bothdirections.Ethernet is a network protocol defined by the IEEE 802.3 standard. Ethernet-basednetworks use MAC Address rather then IP Address to exchange data betweencomputers. By using ARP and adding TCP/IP support, Ethernet devices may beconnected as part of the Internet. An Ethernet LAN typically uses coaxial cable or specialgrades of twisted pair wires. The most commonly installed Ethernet systems are called10BASE-T and provide transmission speeds up to 10 Mbps. Devices are connected tothe cable and compete for access using a Carrier Sense Multiple Access with CollisionDetection (CSMA/CD) protocol.IP (Internet Protocol) is the method or protocol by which data is sent from one computerto another on the Internet.IP address (Internet Protocol address) is a 32-bit number that identifies each senderor receiver of information that is sent in packets across the Internet.IP Netmask is a 32-bit pattern of bits used to determine which part of the IP address isthe network portion and which part is the host portion.MAC (Media Access Control) Address is your computer's unique hardware number.When you're connected to the Internet from your computer, a correspondence tablerelates your IP address to your computer's physical (MAC) address on the LAN.Ping is a utility that tests the network connectivity. It is used to determine if the host iscapable of exchanging information with another host.Port number/Socket number is a way to identify a specific process to which an Internetor other network message is to be forwarded when it arrives at a server. It is apredefined address that serves as a route from the application to the Transport layer orfrom the Transport layer to the application of the TCP/IP system.Sockets are a method for communication between a client program and a serverprogram in a network and defined as "the endpoint in a connection." Informationtransferred across the Internet primarily occurs between sockets.TCP/IP (Transmission Control Protocol/Internet Protocol) is the basic communicationlanguage or protocol of the Internet. When you are set up with direct access to theInternet, your computer is provided with a copy of the TCP/IP program just as everyother computer that you may send messages to or get information from also has a copyof TCP/IP. TCP/IP often is used as a general term to indicate generic access to theInternet.35
Page 1 and 2: Industrial MicroServerEIS-2 and EIS
Page 3 and 4: TABLE OF CONTENTSPart 1: Introducti
Page 5 and 6: NOTES, WARNINGS and CAUTIONSInforma
Page 7 and 8: RX TX ON COL1.3 DescriptionThis dev
Page 9 and 10: 2.3 Parts of the iServer UnitTX RX
Page 11 and 12: 2.4.2 Wiring RS485 InterfaceRS485 i
Page 13 and 14: PART 3NETWORK CONFIGURATION3.1 Netw
Page 15 and 16: 3.5 IP AddressEvery active device c
Page 17 and 18: 4.1 Setup and Operation Using the i
Page 19 and 20: 4.1.3 Modify Device List Entry• U
Page 21 and 22: Timeout: The amount of time that th
Page 23 and 24: 4.2 Setting a New IP Address using
Page 25 and 26: 4.3 Setting a New IP Address over t
Page 27 and 28: 4.5 Telnet SetupTelnet stands for T
Page 29 and 30: 4.6 HTTPGET ProgramYou can setup an
Page 31 and 32: 4.8 Remote Access (Tunneling)To "tu
Page 33 and 34: 4.8.2 Local iServer1. An IP address
Page 35 and 36: 4.9.2 Program Options Setup and Con
Page 37: PART 5SPECIFICATIONSSERIAL INTERFAC
Page 41 and 42: Appendix CIP NetmaskIP Netmask or S
Page 43 and 44: Appendix DASCII Chart Continuation/
Page 47 and 48: Warranty/DisclaimerNEWPORT Electron

EIS-2 & EIS-2-RJ - iServer Industrial MicroServer Manual - NEWPORT

Create successful ePaper yourself

Delete template?

Save as template?