EIS-2 & EIS-2-RJ - iServer Industrial MicroServer Manual - NEWPORT

More documents

Recommendations

Info

PART 2HARDWARE2.1a Mounting on a DIN RailFigure 2.1 MountingTo install unit onto DIN Rail:a) Tilt unit, positionmounting slot onto DINRail, as shown.b) Push unit towards DINRail and it will snap intoplace.2.1b Removal from a DIN RailFigure 2.2 Removal1. Insert flat screw-driverinto tab and pushdownwards.2. Unit will detach from DINRail.2.2 DIP SwitchesThe iServer is shippedwith all DIP switchesin "OFF" position1 To change the IP address fromthe serial port2 To change to default factorysettings3 To enable/disable DHCP4 To enable/disable TerminalServer functionONFigure 2.2 DIP Switches4OFF4321ONOFF4321
2.3 Parts of the iServer UnitTX RX RTNCOMMUNICATIONSCOMMUNICATIONSETHERNETETHERNETRESETRESETRX TX ON COLRX TX ON COLDC POWER INDC POWER IN+ - N/CEIS-2+ - N/CEIS-2-RJFigure 2.3 Parts of the iServer UnitTable 2.1 Parts of iServer UnitSERIAL Screw Terminal Block or RJ45 for RS-232 / RS-485 / RS-422 connections.ETHERNET RJ45 interface for 10BASE-T connection.RESET Button: Used for power reseting the iServer.COL LED (Red) Blinking: Indicates network activities (receiving or sending packets).ON LED (Green) Solid: Indicates good network link.TX LED (Yellow) Blinking: Indicates transmitting data to the serial port.RX LED (Green) Blinking: Indicates receiving data on the serial port.DC Power Supply Section:+ Plus Power Supply Wire connection.- Minus Power Supply Wire connection.5
Page 1 and 2: Industrial MicroServerEIS-2 and EIS
Page 3 and 4: TABLE OF CONTENTSPart 1: Introducti
Page 5 and 6: NOTES, WARNINGS and CAUTIONSInforma
Page 7: RX TX ON COL1.3 DescriptionThis dev
Page 11 and 12: 2.4.2 Wiring RS485 InterfaceRS485 i
Page 13 and 14: PART 3NETWORK CONFIGURATION3.1 Netw
Page 15 and 16: 3.5 IP AddressEvery active device c
Page 17 and 18: 4.1 Setup and Operation Using the i
Page 19 and 20: 4.1.3 Modify Device List Entry• U
Page 21 and 22: Timeout: The amount of time that th
Page 23 and 24: 4.2 Setting a New IP Address using
Page 25 and 26: 4.3 Setting a New IP Address over t
Page 27 and 28: 4.5 Telnet SetupTelnet stands for T
Page 29 and 30: 4.6 HTTPGET ProgramYou can setup an
Page 31 and 32: 4.8 Remote Access (Tunneling)To "tu
Page 33 and 34: 4.8.2 Local iServer1. An IP address
Page 35 and 36: 4.9.2 Program Options Setup and Con
Page 37 and 38: PART 5SPECIFICATIONSSERIAL INTERFAC
Page 39 and 40: APPENDIX AGLOSSARYUser of this manu
Page 41 and 42: Appendix CIP NetmaskIP Netmask or S
Page 43 and 44: Appendix DASCII Chart Continuation/
Page 47 and 48: Warranty/DisclaimerNEWPORT Electron

EIS-2 & EIS-2-RJ - iServer Industrial MicroServer Manual - NEWPORT

Create successful ePaper yourself

Delete template?

Save as template?