PT-AE8000U PT-AT6000E PT-AE8000EA PT ... - Panasonic

3. Extend mode (EXT OPTION menu)This projector has extend mode "EXT OPTION" menu in addition to standard on-screen menus. This mode has Self-Check function, Test Pattern and other functions for Service.3. 1. Procedure to open / close "EXT OPTION" menu.1. When the projector is power ON, press "POWER" button on the main unit or remote control unit to display"POWER OFF" confirmation screen.2. Press the " " button to select "CANCEL" in the "POWER OFF" confirmation screen.3. On the main unit or remote control unit, press the buttons in order of " ▲ ", " ▼ ", " ▲ ", " ▼ " and "ENTER".4. When "MENU" button is pressed at the "EXT OPTION" mode, Extend-mode is closed.3. 2. EXT OPTION Menu and Functions1.FAN FULLMODE1.2.3.4.5.EXT OPTIONFAN FULL MODE OFFAUTO SETUP NORMALSELF CHECKSTATUSFLICKER ADJUST・Setting the cooling fan motor rotation speed.Switching ON "FAN FULLMODE", the rotation level of thefan becomes high-speed rotation (fixed). Moreover, when"FAN FULLMODE" is ON, changing "HIGH ALTITUDEMODE" in OPTION menu becomes impossible (settingFAN FULLMODE is given priority more than HIGHALTITUDE MODE).2.AUTO SETUP・Setting AUTO SETUP mode.- NORMAL: Dot clock is adjusted strictly.- SPECIAL: Dot clock is adjusted roughly.* Do not usually change initial setting (NORMAL).3.SELF CHECK・The content of self checking are displayed.SELF CHECK S/N SD12345678 (13) (1) - Software Version (MM : Main microprocessor, F:FPGA )(1) MM:1.00 SM:1.00(14)* FPGA (Field Programmable Gate Array)F:1.00 IM:1.00(2) XGA60 G-SAVED OK(2) - Input signal Display(3) H 48.48KHZ U-SAVED OK(15)( [NO-SYNC] is displayed when there is no input signal).V 60.60HZ C-SAVED OK(3) ------------ TEMP ------------Input Horizontal/Vertical signal frequency(4) TEMP OK(For the RGB/YPBPR Input only)INTK 22.7/157 INTK ---.-/---(5)(4) -EXST 26.6/148 EXST ---.-/--- (16)The temperature abnormality checkFLTR 88.7/094 FLTR ---.-/---("NG" is displayed for any abnormality)(6) FLTR SENSOR OFFSET 79(5) - Temperature around the air intake port/exhaust port and----------- FAN -------------INTK OK EXST OK (17)Filter sensor (deg C/A/D conversion value)(7) LAMP OK PWR OK(6) - Filter sensor Difference Correction (A/D conversion) ValueIRIS OK-------- MECHANICAL ---------(7) - Rotation check of Intake fan / Lamp fan / Iris fan(8) IRIS OK LENS MEM OK (18)(Displays "NG" when Fan is abnormal condition)----------- LAMP ------------(9) LAMP OK 4000H OK (19) (8) - Iris condition check (Abnormal condition = "NG")(10) COVER OK(9) - Lamp condition check (Abnormal condition = "NG")------- UNIT HISTORY --------(11) TOTAL 11H RESET 0 (20) (10) - Lamp cover installation check (Abnormal condition="NG")12H10 52 12H10(11) - Displays the projector cumulative usage time(12) 0H00 0 0H00(21)0H00 0 0H00(12) - Cumulative usage time (actual time) and Number ofLAMP ON times"OK" display becomes red characters when shutting"Current number : Last reset : Reset of last but one"down because abnormality happened time.(13)- Displays the serial number of the projector.(14)- Software Version (SM : Sub microprocessor, IM : IRIS control microcomputer)(15)- Gamma, Color Unevenness and Crosstalk correction data check (Whether data are stored in the flash ROM)(16)- Thermo sensor (Intake Air / Exhaust Air / Filter Air) measurement value when thermal shutdown(deg C/A/D conversion value)INF - 6