Pt B, Ch 1, Sec 13 Rounding off of scantlings3.13.1.1 Plate thicknesses on metallic hullsThe rounding off of plate thicknesses on metallic hulls is tobe obtained from the following procedure:a) the thickness is calculated in accordance with the rulerequirementsb) the rounded thickness is taken equal to the valuerounded off to the nearest half-millimeter.3.1.2 Stiffener section moduli on metallic hullsStiffener section moduli as calculated in accordance withthe rule requirements are to be rounded off to the neareststandard value; however, no reduction may exceed 3%.Table 2 : Part B Rules requirements applicable for thegeneral arrangement and scantling of other itemsItemsApplicable Chaptersand SectionsAnchors and chain cables Ch 10, Sec 1Rudders Ch 10, Sec 2Windows and sidescuttles Ch 10, Sec 3Shaft brackets Ch 10, Sec 4Independent tanks Ch 10, Sec 5Chain plates Ch 10, Sec 6Solid keel for sailing yachts Ch 10, Sec 770 Bureau Veritas Rules for Yachts July 2006 with February 2008 Amendments
Pt B, Ch 1, Sec 2<strong>SECTION</strong> 2SYMBOLS AND DEFINITIONS1 UnitsTable 1 : Units1.1 Units definition1.1.1 Unless otherwise specified, the units used in theRules are those defined in Tab 1.2 Symbols2.12.1.1 The main symbols are used in the present Rules are:L : Rule length, in m, defined in [3.2]L WL : Waterline length, in m, measured with the shipat rest in calm water, at the full load displacement,as defined in [3.2]L LL : Length according to International Rules asdefined in Pt A, Ch 2, Sec 1, [2.2.1]L h : Length according to EC Directive as defined inPt A, Ch 2, Sec 1, [2.2.1]L HULL : Hull length, in m, defined in [3.3]B : Moulded breadth, in m, defined in [3.5]B WL : Greatest moulded breadth on waterline atdraught T, in m, defined in [3.5]D : Depth, in m, defined in [3.6]T : Full load draught, in m, defined in [3.7]Δ : Full load displacement, in tonnes, at draught T,in sea water (density ρ = 1,025 t/m 3 ).C B : Total block coefficient. For catamarans, C B is tobe calculated for a single hull, assuming Δequal to one half of the ship’s displacementC B =Δ-------------------------------1025 , LB WL TC W : Wave height, in m, defined in [3.10]V : Maximum speed, in knots, of the yachtLCG : Ship’s longitudinal centre of gravitya CG : <strong>Design</strong> vertical acceleration, in g, defined in [3.11]H S : Significant wave height, in m, defined in [3.10].3 Definitions3.1 Moulded base line3.1.1 The moulded base line is the horizontal referenceline tangent to the upper face of bottom plating at midship.In the case of yacht with a solid bar keel, the moulded baseline is to be taken at the intersection between the upper faceof the bottom plating with the solid bar keel at the middle oflength L.<strong>Design</strong>ation3.2 Rule length3.2.1 The rule length L is equal to L WL where L WL is thewaterline length measured with the yacht at rest in calmwater, at the full load displacement.3.3 Hull lengthUsualsymbol3.3.1 The hull length L HULL is equal to the total hull length,from the extreme foreward part of the hull, excluding anyoutfitting protusing, and the extreme aft part.3.4 Ends of rule length L WL and midshipUnitsShip’s dimensions See [2] mHull girder section modulus Z m 3Density ρ t/m 3Concentrated loads P kNLinearly distributed loads q kN/mSurface distributed loads p kN/m 2Thicknesses t mmSpan of ordinary stiffeners andprimary supporting membersSpacing of ordinary stiffeners andprimary supporting membersBending moment M kN.mShear force Q kNStresses σ, τ N/mm 2Section modulus of ordinary stiffenersand primary supporting membersSection area of ordinary stiffenersand primary supporting members3.4.1 Fore endThe fore end (FE) of the rule length L WL (see Fig 1) is the perpendicularto the full load waterline at the forward side ofthe stem.3.4.2 Aft endThe aft end (AE) of the rule length L WL (see Fig 1, is the perpendicularto the full load waterline at a distance L WL aft ofthe fore end.3.4.3 MidshipThe midship is the perpendicular to the waterline at a distance0,5L WL aft of the fore end (see Fig 1).lsmmw cm 3Acm 2July 2006 with February 2008 Amendments Bureau Veritas Rules for Yachts 71
- Page 1 and 2: A-PDF Merger DEMO : Purchase from w
- Page 3 and 4: Pt A, Ch 1, Sec 3SECTION 3SURVEYS1
- Page 5 and 6: Pt A, Ch 1, Sec 5SECTION 5INTERVENT
- Page 7 and 8: Pt A, Ch 2, Sec 1SECTION 1DEFINITIO
- Page 9 and 10: Pt A, Ch 2, Sec 2Table 3 : Charter
- Page 11: Pt B, Ch 1, Sec 1SECTION 1APPLICATI
- Page 15 and 16: Pt B, Ch 1, Sec 4SECTION 4CALCULATI
- Page 17 and 18: Pt B, Ch 10, Sec 5SECTION 5INDEPEND
- Page 19 and 20: Pt B, Ch 11, Sec 1SECTION 1GENERAL
- Page 21 and 22: Pt B, Ch 12, Sec 2SECTION 2RAW MATE
- Page 23 and 24: Pt B, Ch 12, Sec 2The chemical netw
- Page 25 and 26: Pt B, Ch 12, Sec 2This Carbon may u
- Page 27 and 28: Pt B, Ch 12, Sec 23.4 Homologation
- Page 29 and 30: Pt B, Ch 12, Sec 2Table 4 : BalsaVo
- Page 31 and 32: Pt B, Ch 12, Sec 2Table 6 : Meta-ar
- Page 33 and 34: Pt B, Ch 12, Sec 3SECTION 3INDIVIDU
- Page 35 and 36: Pt B, Ch 12, Sec 3Table 1 : Resin /
- Page 37 and 38: Pt B, Ch 12, Sec 3Table 4 : Element
- Page 39 and 40: Pt B, Ch 3, Sec 1c) Lightweight che
- Page 41 and 42: Pt B, Ch 3, Sec 2Figure 1 : Severe
- Page 43 and 44: Pt B, Ch 3, Sec 2where:F : Wind for
- Page 45 and 46: Pt B, Ch 3, App 2APPENDIX 2TRIM AND
- Page 47 and 48: Pt B, Ch 4, Sec 2SECTION 2DESIGN LO
- Page 49 and 50: Pt B, Ch 6, Sec 3SECTION 3SPECIFIC
- Page 51 and 52: Pt B, Ch 6, Sec 3Figure 2 : Rig loa
- Page 53 and 54: Pt B, Ch 7, Sec 1SECTION 1 HYDRODYN
- Page 55 and 56: Pt B, Ch 7, Sec 1Figure 4 : Load ar
- Page 57 and 58: Pt B, Ch 7, Sec 1• for monohull -
- Page 59 and 60: Pt B, Ch 7, Sec 2SECTION 2BOTTOM SL
- Page 61 and 62: Pt B, Ch 9, Sec 1SECTION 1GENERAL1
- Page 63 and 64:
Pt C, Ch 1, Sec 1Table 1 : Inclinat
- Page 65:
Pt C, Ch 1, Sec 13.4 Safety devices