IM3004s User Guide v2.2.pdf - ICS-IQ.com

More documents

Recommendations

Info

Chapter 5 – Operational ProceduresChapter 5:Operational Procedures29
Chapter 5 – Operational ProceduresPreparing to CopyThis section describes the recommended procedure to follow when preparing to performan operation. References to PATA or S-ATA drives in this section, requires use ofappropriate adapters1. Prepare Source Drive• Configure the Source Drive’s SCSI Address ID to a value other than 7.• Verify use of valid partitions• Verify drives are Virus-free• Recommend use of defect free drives.• Defragmented drive.• When using PATA drives, verify that the Source drive jumper block is properlyconfigured. For P-ATA drives the jumper block should be set for “Single/Master”operation. For SAS or SATA drives, the drive’s default jumper block settings arerecommended.• The drive detected in this position will be listed in the Active Source Drive Panel.2. Prepare the Target Drive(s)• Configure the Target Drive’s SCSI Address ID to a value other than 7.• Recommend use of defect free drives.• For best transfer rates use drives with same performance properties.NOTE: By default, all ports including the dedicated Target drive ports are Write-Protected. The Write-Protection feature of all Target drive ports willautomatically be disabled if the selected operational mode requires writing tothe Target drive(s).29
Page 1 and 2:
User GuideFor theImage MASSter IM30
Page 3 and 4:
ContentsContentsCHAPTER 1: INTRODUC
Page 5 and 6:
ContentsConfirm Master and Target d
Page 7 and 8:
Technical Support .................
Page 9 and 10:
Chapter 1 - IntroductionOverviewThe
Page 11 and 12: Chapter 1 - IntroductionAbout this
Page 13 and 14: Chapter 2 - Quick StartQuick Start
Page 15 and 16: Chapter 2 - Quick Start15. After th
Page 17 and 18: Chapter 3 - InstallationSetup1. Car
Page 19 and 20: Chapter 3 - InstallationHardware De
Page 21 and 22: Chapter 3 - InstallationSCSI Drive
Page 23 and 24: Chapter 4 - OperationChapter 4: Ope
Page 25 and 26: Chapter 4 - OperationAdvanced Drive
Page 27 and 28: Chapter 4 - Operation• File Forma
Page 29 and 30: Chapter 4 - OperationWipeOutThe Wip
Page 31 and 32: Chapter 4 - OperationNavigation Bar
Page 33 and 34: Chapter 4 - OperationAbortSelecting
Page 35 and 36: Chapter 4 - OperationPercent of Dis
Page 37 and 38: Chapter 4 - OperationIntelligent Co
Page 39 and 40: Chapter 4 - OperationBlock Map Copy
Page 41 and 42: Chapter 4 - OperationSelect Multipl
Page 43 and 44: Chapter 4 - Operationdesignated cod
Page 45 and 46: Chapter 4 - OperationHash TargetsUs
Page 47 and 48: Chapter 4 - OperationMultiMASSter C
Page 49 and 50: Chapter 4 - OperationSets the selec
Page 51 and 52: Chapter 4 - OperationAutomation Set
Page 53 and 54: Chapter 4 - OperationAdvanced Drive
Page 55 and 56: Chapter 4 - OperationCalibrate Dete
Page 57 and 58: Chapter 4 - OperationSpeed Optimiza
Page 59 and 60: Chapter 4 - OperationWrite-Protect
Page 64 and 65: Chapter 5 - Operational Procedures3
Page 66 and 67: Chapter 5 - Operational ProceduresD
Page 68 and 69: Chapter 5 - Operational ProceduresS
Page 70 and 71: Chapter 5 - Operational ProceduresC
Page 76 and 77: Chapter 5 - Operational ProceduresP
Page 78 and 79: Chapter 5 - Operational ProceduresT
Page 80 and 81: Appendix A:DefinitionsImage copyThe
Page 82 and 83: SCA-80 InterfaceSCSI interface whic
Page 84 and 85: Chapter 6 - Product InformationSCSI
Page 86 and 87: Chapter 6 - Product InformationAppe
show all

IM3004s User Guide v2.2.pdf - ICS-IQ.com

Create successful ePaper yourself

Delete template?

Save as template?