Spaenaur

Series 82 Selection Guide
To select correct fastener
1. Choose a receptacle. (Note any frame thickness limitations).
2. To select a stud,
a) measure your Outer Panel Thickness or Total Material Thickness
(note with receptacle will tell you which to use).
b) if adjustment formula is shown under receptacle part number, apply
this formula to your measurement.
c) if sealing washers, stud ejector springs or wear washers will be
used, apply proper adjustment formulas to your measurement.
d) use measurement (or adjusted measurement) to find part number
in chart.
3. Choose a retainer.
OUTER PANEL
4. Review the stud installation procedure.
5. Order each part and tool separately.
FRAME
See page L174 for studs.
TOTAL
MATERIAL
THICKNESS
FRAME
Quarter Turn Fasteners
OUTER PANEL
Attaches à quart de tour
OUTER PANEL
THICKNESS
Series 82 Leaf Spring Receptacles
FLANGE,
GASKET or
SPACE
For Riveting - with Base
SPAENAUR No.
110-038
Mfr. #82-35-302-15
5.7
(.22)
REF.
3
(.13)
19 (.750)
11.2 (.44)
26.6 (1.05)
Countersink or dimple
Hole size, Ø .098 in. for 3 ⁄32 rivet
Ø 2.6 mm for 2.5 mm rivet
Swell rivet shank to
+0.25 +.010
Ø 2.7 (.107 )
9.5 (.38)
-0.00
+.004
Ø 2.6 (.102 -.001 )
-.000
Material and Finish
RECEPTACLE SPRING:
1064 Steel DACROTIZED†
BASE: 1010 Steel,
DACROTIZED†
Spring must float
freely as before
riveting.
L
For Riveting - without Base
SPAENAUR No.
110-182
Mfr. #82-35-295-15
5.7
(.22)
3
(.13)
19 (.750)
11.9 (.47)
26.2 (1.03)
Countersink or dimple
Hole size, Ø .098 in. for 3 ⁄32 rivet
Ø 2.6 mm for 2.5 mm rivet
Swell rivet shank to
+0.25 +.010
Ø 2.7 -0.00 (.107 -.000 )
Material and Finish
RECEPTACLE SPRING:
1064 Steel DACROTIZED†
EYELET: Steel,
DACROTIZED†
2.6
Ø (.102)
Ø 7.9 (.31)
9.5 (.38)
Ø 5.2 (.205)
Spring must float
freely as before
riveting.
CATALOG 13
For Welding
SPAENAUR No.
110-184
Mfr. #82-35-303-15
3
(.13)
11.2
(.44)
19 (.750)
26.6 (1.05)
5.4
(.21)
Material and Finish
RECEPTACLE SPRING: 1064 Steel
DACROTIZED†
BASE: 1010 Steel, DACROTIZED†
WELDING STUDS: Steel copper plate.
SPAENAUR No.
110-185
Pilot Clamp
Mfr. #82-0-6948-11
Spring must float
freely as before
welding.
†Registered tradename of Metal
Coatings International, Inc.
Rivet must not melt
over onto spring.
9.5 (.38)
continued …
Tel: 1-800-265-8772 Fax: 519-744-0818
Use with Series 82
receptacles shown
on this and following
pages.
L173
02 Oct 01