cvs 2400 series smart positioner product description - CVS Controls

More documents

Recommendations

Info

CVS Controls Ltd. Product Manual: YT-2400 Smart Positioner 7. Ensure the YT-2400L feedback lever is level at 50% of the valve stroke. If not, make it level by moving the bracket of feedback link bar. If the YT-2400 is installed and not level at 50% of the valve stroke, product linearity becomes worse. CVS Controls Ltd. Process Management And Instrumentation Feedback lever being leveled correctly 8. Check the valve stroke. The numbers indicating stroke are engraved on the YT-2400L feedback lever. Set the connection bar attached on the actuator clamp on the number so the feedback lever is applicable to the valve stroke as shown in the following picture. 20 30 40 50 60 70 20 30 40 50 60 70 NOTE: After installation, operate the valve from 0% stroke to 100% when using the air filter regulator on the actuator. When the stroke is both at 0% and 100%, the feedback lever should not reach the lever stoppers on the backside of the YT-2400. If the feedback lever reaches the lever stopper, move the attachment position of the YT-2400L to the direction becoming more distant from the yoke center. 90% Stroke 30mm Stroke 70mm Installation position of the connection bar for the valve stroke 50% 9. If the YT-2400L is installed correctly as shown in the above procedures, tighten the nuts and bolts on the bracket and feedback lever connection bar. YT-2400R Installation YT-2400R is used for a rotary motion valve such as a ball or butterfly valve using rack and pinion, scotch yoke or complex type actuators whose stem is rotated 90 degrees. YT-2400R consists of the following components: 1. YT-2400R main body 2. Fork spring & lever attach onto the actuator 3. 1 set of brackets 4. 4pcs of Hexagon head bolt M8x1.25P 5. 4pcs of M8 plate washer YT-2400R Installation Example 8 Check whether or not the lever stopper and feedback lever is contacted YT-2400R Installation example of fork lever YT-2400R Installation example of NAMUR shaft No Touch
CVS Controls Ltd. Product Manual: YT-2400 Smart Positioner Installing YT-2400R with Bracket The YT-2400R is supplied with a standard bracket. The bracket consists of 2 parts and can be used with a fork lever and NAMUR shaft. The bracket is assembled in the factory based on 20mm of actuator stem height. If the actuator stem height exceeds 20mm, such as 30mm, or 50mm, reassemble the bracket adjusting to the height. Referring to the following table, check the hole positions. H: 50 H: 30 H: 20,30 A-L H: 50 B-L H: 20 Actuator Stem Height (H) 15 90 42 1. In general, the height of an actuator (H) is 20, 30, or 50mm. After checking (H), assemble brackets as explained in the previous paragraph. The bracket is set as 20mm type in the factory. CVS Controls Ltd. Process Management And Instrumentation 165.6 130 80 164.6 45 5 30 90 H: 20 H: 30 H: 50 Actuator Stem Actuator Actuator Stem Height (H=20mm) 15 60 H: 50 B-R A-R H: 20,30 Bracket Assembly method by actuator stem height H Markings of Bolt Holes 9 Upper Bracket A Upper Bracket B A-L B-L A-R B-R 20mm H: 20 H: 20, 30 H: 20 H: 20, 30 30 mm H: 30 H: 20, 30 H: 30 H: 20, 30 50 mm H: 50 H: 50 H: 50 H:50 Ex: In case that H is 30mm, A-L should be locked in H:30 hole B-L in H: 20,30; A-R in H:30, B-R in H:20, 30 with bolts. 20 2. Attach the bracketed YT-2400R to the actuator by using the supplied bolts. The size of the bracket hole is 6mm. When tightening the bolts, use the spring washer or similar washer for firm attachment to the actuator. The direction of the bracket is different from the operating condition, but normal direction is shown in the following picture. So that, when the piping of the actuator and YT-2400R is in direction A, the bracket hole and indicator attached on the bottom of the YT-2400R main shaft should be the same direction as the half circle. Direction A Attachment Direction of bracket and Actuator 3. Set the rotation position of the actuator stem at the initial zero point which is stroke 0%. In the case of the spring return type actuator, the actuator stem is always rotated at zero point without supply pressure, it is easy to check zero point. If the actuator is double acting, check whether it is clockwise or counter-clockwise or the rotation direction of the actuator stem with using supply pressure. 4. Set the actuator stem at the initial zero point and install the fork lever as in the following picture. Ensure the position of the initial zero point when the actuator stem is clockwise or counter-clockwise. Installation angle of the fork lever should be 45 degrees based on the linear shaft, but the angle is not related to the NAMUR shaft.
Page 1 and 2: CVS 2400 SERIES SMART POSITIONER PR
Page 3 and 4: FEATURES and FUNCTIONS 1. There are
Page 5 and 6: FEATURES & FUNCTIONS CVS Controls L
Page 7: Installing YT-2400L with Bracket 1.
Page 11 and 12: Supply Pressure Condition 1. Dry ai
Page 13 and 14: 5. Ensure not to change the polarit
Page 15 and 16: The shape and position of buttons a
Page 17 and 18: Auto 2 Callibration (AUTO2) All par
Page 19 and 20: KP (1) - (3) Adjustment method and
Page 21 and 22: Adjustment of zero point ((1)-(4)),
Page 23 and 24: Adjustment of Tight Shut Open (TSHU
Page 25 and 26: Error / Warning Code Code Descripti
Page 27 and 28: NOTES CVS Controls Ltd. strives for

cvs 2400 series smart positioner product description - CVS Controls

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?