ROTO SILENTA 630 RS - HettichLab

More documents

Recommendations

Info

EN Manufacturer Andreas Hettich GmbH & Co. KG D-78532 Tuttlingen Model ROTO SILENTA 630 RS Type 5005-08 5005-88 5005-98 Mains voltage 208–220 V +6/-10% 3~ (+N) +PE Mains frequency 50 - 60 Hz Connected load 9000 VA 8700 VA 5200 VA Current consumption 25 A 24 A 14 A Cooling medium R 404A Max. capacity 12000 ml Allowed density 1.2 kg/dm 3 Speed (RPM) 4500 Force (RCF) 6498 Kinetic energy 215000 Nm Obligatory inspection (BGR 500) Ambient conditions (EN / IEC 61010-1) yes Set-up site Indoors only Altitude Up to 2000 m above sea level Ambient temperature 5°C to 30°C 5°C to 40°C Humidity Maximum relative humidity 80% for temperatures up to 31°C, linearly decreasing to 50% relative humidity at 40°C. Excess-voltage category (IEC 60364-4-443) Pollution degree 2 Device protection class Not suitable for use in explosion-endangered areas. EMC Emitted interference, EN / IEC 61326-1, Class B Interference immunity Noise level (dependent on rotor) 62 dB(A) Dimensions Width 813 mm Depth 1015 mm Height 973 mm Weight approx. 401 kg 42/136
4 Notes on safety No claim of warranty will be considered by the manufacturer unless ALL instructions in this manual have been followed. The centrifuge should be installed on a good, stable base. Before using the centrifuge absolutely check the rotor for firm placement. When the centrifuge is running, according to EN / IEC 61010-2-020, no persons, dangerous substances or objects may be within the safety margin of 300 mm around the centrifuge. Rotors, suspensions and accessories that possess traces of corrosion or mechanical damage or if their term of use has expired may not be used any longer. The centrifuge may no longer be put into operation when the centrifuging chamber has safetyrelated damages. With swing-out rotors the trunnions must be regularly lubricated (Hettich Lubricating Grease No. 4051) in order to ensure consistent swinging out of the hangers. For centrifuges without temperature control, when the room temperature is increased and/or if the device is frequently used, the centrifuging chamber could be heated up. Therefore, it can't be ruled out that the sample material might be changed due to the temperature. Before the initial operation of your centrifuge you should read and pay attention to the operating instructions. Only personnel that has read and understood the operating instructions are allowed to operate the device. Along with the operating instructions and the legal regulations on accident prevention, you should also follow the recognised professional regulations for working in a safe and professional manner. These operating instructions should be read in conjunction with any other instructions concerning accident prevention and environmental protection based on the national regulations of the country where the device is to be used. This centrifuge is a state-of-the-art piece of equipment which is extremely safe to operate. However, it can lead to danger for users or others if used by untrained staff, in an inappropriate way or for a purpose other than that it was designed for. The centrifuge must not be moved or knocked during operation. In case of fault or emergency release, never touch the rotor before it has stopped turning. To avoid damage due to condensate, when changing from a cold to a warm room the centrifuge must either heat up for at least 3 hours in the warm room before being connected to the mains, or run hot for 30 minutes in the cold room. Only the rotors and accessories approved by the manufacturer for this device may be used (see chapter "Anhang/Appendix, Rotoren und Zubehör/Rotors and accessories"). Before centrifuge vessels are used which are not listed in the chapter "Appendix, Rotors and accessories", the user must make sure they can be used by asking the manufacturer. The centrifuge rotor may only be loaded in accordance with the chapter "Loading the rotor". When centrifuging with maxim revolutions per minute the density of the materials or the material mixtures may not exceed 1.2 kg/dm 3 . The centrifuge may only be operated when the balance is within the bounds of acceptability. The centrifuge may not be operated in explosion-endangered areas. The centrifuge must not be used with: inflammable or explosive materials materials that react with one another producing a lot of energy. EN 43/136
Page 1 and 2: ROTO SILENTA 630 RS DE Bedienungsan
Page 3 and 4: EG-Konformitätserklärung EC Decla
Page 5 and 6: Für Hettich Zentrifugen gültige N
Page 7 and 8: Standards and regulations applied t
Page 9 and 10: Normes et prescriptions valables po
Page 11 and 12: Norme e direttive valide per le cen
Page 13 and 14: Andreas Hettich GmbH & Co. KG Föhr
Page 15 and 16: 20 Anzeige der maximalen RCF des Ro
Page 17 and 18: 3 Technische Daten Hersteller Andre
Page 19 and 20: 4 Sicherheitshinweise Werden nicht
Page 21 and 22: 5 Bedeutung der Symbole Symbol am G
Page 23 and 24: 10 Ein- und Ausbau des Rotors A C D
Page 25 and 26: START STOP PROG RCL STO Anlauf-Para
Page 27 and 28: 15 Programmierung 15.1 Programm-Ein
Page 29 and 30: 24 Datums- und Uhrzeit-Einstellung
Page 31 and 32: 29 Kühlung (nur bei Zentrifuge mit
Page 33 and 34: 35 Pflege und Wartung Das Gerät ka
Page 35 and 36: 35.2.5 Rotoren und Zubehör mit beg
Page 37 and 38: 37 Rücksendung von Geräten Wird d
Page 39 and 40: 20 Displaying the maximum RCF of th
Page 41: 3 Technical specifications Manufact
Page 45 and 46: 5 Symbol meanings Symbol on the dev
Page 47 and 48: 10 Installation and removal of the
Page 49 and 50: START STOP PROG RCL STO Run-up para
Page 51 and 52: 15 Programming 15.1 Entering / modi
Page 53 and 54: 24 Setting the date and time It is
Page 55 and 56: 31 Relative centrifugal force (RCF)
Page 57 and 58: 35.1.3 Removal of radioactive conta
Page 59 and 60: 36 Faults If the fault cannot be el
Page 61 and 62: Table des matières 1 Utilisation c
Page 63 and 64: 1 Utilisation conforme Concernant l
Page 65 and 66: Fabricant Andreas Hettich GmbH & Co
Page 67 and 68: En cas de centrifugation de substan
Page 69 and 70: 7 Déballer et mettre la centrifuge
Page 71 and 72: 12 Fermeture des systèmes de sécu
Page 73 and 74: 14.3 Accélération relative de cen
Page 75 and 76: 16.2 Fonctionnement en continu Par
Page 77 and 78: 27 Interrupteur à clé (uniquement
Page 79 and 80: 31 Accélération centrifuge relati
Page 81 and 82: 35.1.2 Désinfection des surfaces
Page 83 and 84: 36 Défauts Si l'erreur ne peut pas
Page 85 and 86: Indice 1 Conformità di impiego....
Page 87 and 88: 1 Conformità di impiego L'apparecc
Page 89 and 90: Costruttore Andreas Hettich GmbH &
Page 91 and 92: Se vengono centrifugate sostanze pe
Page 93 and 94:
7 Disimballaggio e installazione de
Page 95 and 96:
12 Chiudere i sistemi biologici di
Page 97 and 98:
14.4 Parametri di avviamento e arre
Page 99 and 100:
17 Modifica delle impostazioni dura
Page 101 and 102:
28.1 Collegare i programmi Un colle
Page 103 and 104:
32 Centrifugazione di sostanze o di
Page 105 and 106:
35.2 Rotori ed accessori 35.2.1 Pul
Page 107 and 108:
36 Guasti Se non si riesce a elimin
Page 109 and 110:
39 Anhang / Appendix 39.1 Rotoren u
Page 111 and 112:
4174 5052 + 5057 Ausschwingrotor 4-
Page 113 and 114:
4174 4522-A Ausschwingrotor 4-fach
Page 115 and 116:
4174 4524-A 4546-A 4591-A 4595-A Au
Page 117 and 118:
4174 4579-A + 4255 / 4255-P 4) Auss
Page 119 and 120:
4174 4547-A + 5621 Ausschwingrotor
Page 121 and 122:
4174 4547-A + 5621 4523-A Ausschwin
Page 123 and 124:
Page 125 and 126:
Page 127 and 128:
4176 4522-A Ausschwingrotor 6-fach
Page 129 and 130:
4176 4524-A 4546-A 4591-A 4595-A Au
Page 131 and 132:
4176 4579-A + 4255 / 4255-P 4) Auss
Page 133 and 134:
4176 4547-A + 5621 Ausschwingrotor
Page 135 and 136:
4176 4547-A + 5621 4523-A Ausschwin
show all

ROTO SILENTA 630 RS - HettichLab

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?