Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
Operation<br />
Operating elements<br />
Every <strong>80</strong>00 cycles<br />
Replace the brush (see "Maintenance<br />
tasks").<br />
Maintenance Works<br />
Emptying the coin cassette<br />
A Device with coin slot<br />
B Device with start button<br />
1 Throwing in the coin<br />
2 Indicator lamp<br />
3 Coin return<br />
4 Start button<br />
5 Mat feeder<br />
6 Mat ejector<br />
START<br />
Cleaning the mat<br />
Device with coin slot:<br />
Insert a coin in the coin slot.<br />
The device starts.<br />
Device with start button:<br />
Press the start button.<br />
The device starts.<br />
Turn the side of the mat to be<br />
cleaned downwards.<br />
Push the mat into the mat feeder<br />
and hold it.<br />
Insert, withdraw, and turn the<br />
mat in the device several times<br />
until all points of the mat have<br />
been cleaned.<br />
Pull the mat out of the device.<br />
Note:<br />
If the mat is released, it will move through<br />
the device and be ejected at the mat ejector.<br />
Settings<br />
Setting the run time<br />
Note:<br />
The adjustable run time applies to the insertion<br />
of one of the following coins:<br />
– 50 Eurocents<br />
– 50 British pence<br />
– 1 Swiss franc<br />
– 1 Polish złoty<br />
– 5 Norwegian Kroner<br />
Remove the lid (see "Maintenance and<br />
care/Maintenance tasks/Removing the<br />
lid").<br />
1 "PRG" button<br />
2 LED 3<br />
3 LED 1<br />
4 "P1" button<br />
5 Control<br />
Press the "PRG" button and hold it<br />
down until LED 3 illuminates.<br />
The "adjustment" operating mode is activated.<br />
Note:<br />
The "adjustment" operating mode will end if<br />
no buttons have been pressed for 10 seconds.<br />
The adjustment begins with a run time of 0<br />
seconds.<br />
Maximum run time is 10 minutes. If this setting<br />
is reached, LED 1 will flash quickly.<br />
Press the "P1" button briefly.<br />
LED 1 flashes quickly and the run time<br />
is increased by 5 seconds.<br />
Press and hold the "P1" button.<br />
LED 1 flashes slowly and the run time is<br />
increased by 30 seconds.<br />
Set the desired run time by pressing the<br />
"P1" button repeatedly.<br />
To confirm the set run time, press the<br />
"PRG" button until LED 3 flashes quickly:<br />
The run time has now been saved.<br />
Shutting down<br />
Set main switch to “0”.<br />
Maintenance and care<br />
DANGER<br />
Risk of injury due to inadvertently starting<br />
up device and also due to electric shock.<br />
Before starting any maintenance and<br />
care work, turn the main switch off "0"<br />
and ensure that it will not be turned on<br />
accidentally.<br />
Daily<br />
For device with coin slot: Empty the<br />
coin cassette (see "Maintenance<br />
tasks").<br />
Empty the dirt receptacle (see "Maintenance<br />
tasks").<br />
Check the general condition of the device.<br />
Have damaged parts replaced.<br />
Weekly<br />
Remove dirt from the mat ejector.<br />
Clean the device.<br />
Every 500 cycles<br />
Lubricate the locks with penetrating oil<br />
(Caramba, WD 40).<br />
1 Door<br />
2 Lock<br />
3 Coin cassette<br />
Open door.<br />
Remove and empty the coin cassette.<br />
Removing the front cover<br />
1 Lock<br />
2 Cover<br />
Open locks.<br />
Remove cover.<br />
Emptying the dirt receptacle<br />
Remove the front cover (see above).<br />
1 Dirt receptacle<br />
(not included in delivery)<br />
Remove and empty the dirt receptacle.<br />
Reinsert the dirt receptacle.<br />
Install and lock the cover.<br />
8 EN<br />
- 2