NPort 5110 User's Manual - Moxa

More documents

Recommendations

Info

NPort 5110 Series User’s Manual Configuring Windows Administrator 6. Select the COM No. COM ports that are “In use” or “Assigned” will also be indicated in this drop-down list. If you select multiple serial ports or multiple NPort 5110s, remember to check the “Auto Enumerating” function to use the COM No. you select as the first COM No. Hi-performance mode is the default for Tx mode. If the driver finishes sending data out to the NPort 5110, the driver will respond to the program with “Tx Empty.” Under classical mode, the driver will not notify the user’s program that the Tx is finished until all Tx data has been sent out from the NPort 5110; this mode will cause lower throughput. Classical mode is recommended if you want to ensure that all data is sent out before doing more processing,. 6-25
NPort 5110 Series User’s Manual Configuring Windows Administrator Enable/Disable Tx/Rx FIFO. If disabled, NPort 5110 will send one byte each time the Tx FIFO becomes empty; and an Rx interrupt will be generated for each incoming byte. This will result in a faster response and lower throughput. If you want to use XON/XOFF flow control, we recommend setting FIFO to Disable. Fast Flush (only flush local buffer) We have added one optional Fast Flush function to Moxa’s new NPort Real COM driver. The new function is available in versions 1.2 and higher of NPort Administrator Suite for NPort. For some applications, the user’s program will use the Win32 “PurgeComm()” function before it reads or writes data. With our design, after the program uses this Purge Comm() function, the NPort driver will keep querying NPort’s firmware several times to make sure there is really no data queued in the NPort firmware buffer, rather than just flushing the local buffer. This kind of design is used because of some special considerations. However, it might take more time (about several hundred milliseconds) than a native COM1, because it needs to work via Ethernet. That’s why the native COM ports on the motherboard can work fast with this function call, but NPort requires much more time. In order to accommodate other applications that require a faster response time, the new NPort driver implements a new “Fast Flush” option. Note that by default, this function is disabled. To begin with, make sure there are some “PurgeComm()” functions being used in your application program. In this kind of situation, you might find that your NPort exhibits a much poorer operation performance than when using the native COM1 port. Once you have enabled the “Fast Flush” function, you can check to see if there has been an improvement in performance. By default, the optional “Fast Flush” function is disabled. If you would like to enable this function, from the “NPort Administrator,” double click on the COM ports that are mapped to the NPort, and then select the “Fast Flush” checkbox. You should find that when “Fast Flush” is enabled, the NPort driver will work faster with “PurgeComm().” 6-26
Page 1 and 2:
NPort 5110 Series User’s Manual F
Page 3 and 4:
Table of Contents Chapter 1 Introdu
Page 5 and 6:
Chapter 1 Introduction 1 Welcome to
Page 7 and 8:
NPort 5110 Series User’s Manual I
Page 9 and 10:
NPort 5110 Series User’s Manual G
Page 11 and 12:
Chapter 3 Initial 3 IP Address Conf
Page 13 and 14:
Page 15 and 16:
Page 17 and 18:
Page 19 and 20:
Chapter 4 Choosing 4 the Proper Ope
Page 21 and 22:
NPort 5110 Series User’s Manual C
Page 23 and 24:
Chapter 5 Web 5 Console Configurati
Page 25 and 26: NPort 5110 Series User’s Manual W
Page 53 and 54: NPort 5110 Series User’s Manual C
Page 75: NPort 5110 Series User’s Manual C
Page 83 and 84: The following topics are covered in
Page 85 and 86: NPort 5110 Series User’s Manual I
Page 87 and 88: NPort 5110 Series User’s Manual P
Page 89 and 90: Appendix B Well B Known Port Number
Page 93 and 94: NPort 5110 Series User’s Manual S
Page 97 and 98: NPort 5110 Series User’s Manual A
Page 101: NPort 5110 Series User’s Manual S
show all

NPort 5110 User's Manual - Moxa

Create successful ePaper yourself

Delete template?

Save as template?