User Manual - Snap Studios

Recommendations

Info

1 1 3 4 2 3 2 54 Drive There are three drive modes: Single, Continuous and when a film magazine is attached, Multi exposure. They are all accessed by pressing the DRIVE button on the grip. Single In Single mode, an exposure is made when the shutter release button is pressed, the film is advanced to the next frame and the camera is made ready for the next exposure. To make the next exposure however, you must first release the shutter release button and then press again. In camera active mode: 1) Press the DRIVE button on the grip. 2) Turn the front control wheel to: Single 3) Press Save to store the setting. Continuous In Continuous mode, the camera automatically continues to make exposures and advance the film for the next exposure as long as you maintain pressure on the shutter release button (to the end of the film) at a rate of approximately 2 frames per second. In camera active mode: 1) Press the DRIVE button on the grip. 2) Turn the front control wheel to: Continuous 3) Press Save to store the setting. Multi exposure (with film magazine only) In Multi exposure mode, the camera does not advance the film after the first exposure, only at the end of the pre-determined number of exposures. The frame options are: 2, 3, 4, 5 and ‘No limit’. In camera active mode: 1) Press the DRIVE button on the grip. 2) Turn the front control wheel to: Multi exp. 3) Turn the rear control wheel to select the number of frames required. 4) Press Save (DRIVE button) to store the setting. 5) The LCD will display firstly that no frames have been exposed in the multi-sequence (For example, in the case of a three exposure setting the display will be Exp:0/3). 6) Press the shutter release button to make the first exposure. 7) The LCD will display how many frames have been exposed in the sequence (In the case of a three exposure setting the display will now be Exp:1/3. After the next exposure, the LCD would then display 2/3 etc) 8) You can change your mind at any time to exit the sequence by pressing the DRIVE button to advance the film to the next frame. The camera is then prepared for another new multi exposure sequence according to the initial setting. Please note this function is only available when a film magazine is attached. It is not available with digital backs.
1 2 3 4 5 ON.OFF (PROFILES/ESC) 55 Profiles The profiles feature allows rapid access to pre-determined combinations of settings that increase the speed and security of workflow. One example might be in a social situation where there might be a need for formal outdoor portraiture followed by informal indoor handheld flash-assisted wide-angle shots, both situations requiring very different settings in a stressful environment. By predetermining the relevant settings required beforehand for each situation, they can be saved collectively as a profile. By calling up the profile, you can then be assured that all the settings are correct at the press of one button. For example, you might choose – autofocus single, bracketing, programmed exposure, etc – for outdoors. Once set, you would click on the red PROFILES button, select a profile name and press SAVE. A new name can be entered for the new profile - ‘Outdoors’, for instance - and saved again. New settings are made for the indoor shots changing to flash, Pv setting, etc and the procedure repeated. By simply accessing ‘Outdoors’ or ‘Indoors’ in the profile list, all the relevant settings will be instantly and correctly implemented to match the situation. There are four profiles: Standard, Full auto, Studio and Fill flash. All except Standard can be changed and renamed. The pre-set profiles feature the following: Standard: normal flash, autofocus (single), single drive, autoexposure (aperture priority), average metering, user button -None Full auto: normal flash, autofocus (single), single drive, programmed exposure, centre weighted metering, user button -None Studio: normal flash, manual focus, single drive, manual exposure, spot metering. user button - AF drive Fill flash: normal flash (-1.7EV), autofocus (single), single drive, autoexposure, average metering. All user profiles can be restored to default values again simply by removing the battery and holding down the MENU and DRIVE buttons together and while keeping them depressed, replace the battery. There will be an audible signal that denotes the restoration. Making a profile 1) Activate the camera and go through the various settings (for example, autofocus, aperture priority, fill flash exposure compensation, etc.) you require for the particular purpose and save them as you go. 2) When all the required settings have been made, click (not press!) the PROFILES button (ON.OFF button) on the grip and the profile screen will appear. 3) Use either the front or rear control wheel to scroll through the list of profiles. Choose a profile name (except Standard). You can either save the new settings under this name or change the name you want to change. 4) Press Save (DRIVE button). The Profile name screen is then displayed where you can rename the profile to what suits you (see section Imprint / Text 4.2.2 further on in this manual for procedure details). 5) Press Save (DRIVE button) to keep the combination of settings with the new name. To use a profile from the main screen, press the PROFILES button to reach the profiles screen again. Scroll down the list to the profile
Page 1 and 2:
1 User Manual (Manual (V1/English)
Page 3 and 4: Congratulations! Welcome to the fla
Page 5 and 6: What’s in the box Your new Hassel
Page 7 and 8: 1 Quick Start This section is a qui
Page 9 and 10: 13 14 15 16 17 18 19 20 21 22 B A 2
Page 11 and 12: 33 35 34 36 11 33. From the inactiv
Page 13 and 14: 2 Function Control & Display ■ LC
Page 15 and 16: Grip LCD Typical camera grip displa
Page 17 and 18: Viewfinder LCD Typical viewfinder d
Page 19 and 20: A B C D E I F G H Shutter release b
Page 21 and 22: P Q R There are also two control bu
Page 23 and 24: 1 3 5 7 1 2 2 4 6 8 23 Carrying str
Page 25 and 26: 9 10 25 • Long-term storage of ba
Page 27 and 28: 4 Viewfinder ■ Multi-mode light m
Page 29 and 30: 5 Lenses ■ Rapid and accurate aut
Page 31 and 32: 10 11 12 7 8 9 Lens focus setting t
Page 33 and 34: 6 Film Magazines ■ Automatic 120/
Page 35 and 36: G H I K L J 35 a time-out of five s
Page 37 and 38: A B 1 2 3 4 5 Film speed Film lengt
Page 39 and 40: 1 2 4 3 5 1 1 2 2 39 Film loading T
Page 41 and 42: 41 Hasselblad provides a number of
Page 43 and 44: Approval Architecture (IAA), an enh
Page 45 and 46: Average (45 x 37 mm) ≈ 70% Centre
Page 47 and 48: 4 1 EXP 2 3 47 A ‘+ 0.3’ abo
Page 49 and 50: 1 3 5 A B +/- 2 4 49 Alternativ
Page 51 and 52: Power The camera can be set at two
Page 53: 1 AF 2 3 53 Continuous At Contin
Page 57 and 58: 10 Advanced Features ■ Programmab
Page 59 and 60: There are a number of more advanced
Page 61 and 62: 2 Bracketing 61 Bracketing options
Page 63 and 64: 1 2 3 4 5 6 Number of exposures hig
Page 65 and 66: Standby timeout 1 • 5s • 10s
Page 67 and 68: AE lock / Quick adjust 22 • Exp r
Page 69 and 70: 1 2 5 6 7 3 4 69 Image
Page 71 and 72: 2 4 5 AF Sel. 1 2 3 4 5 6 7 3
Page 73 and 74: 1 3 5 7 2 4 6 73 4.4 Syst
Page 75 and 76: The H2 can be used together with mo
Page 77 and 78: 1 3 5 FLASH AE-L 2 4 6 77 Sepa
Page 79 and 80: There are a number of optional acce
Page 81 and 82: Glossary of Terms For the sake of c
Page 83 and 84: True exposure Shutter position Open
Page 85 and 86: Technical specifications Camera Typ
Page 87 and 88: External dimensions approx. 155 mm
Page 89 and 90: Problems, Equipment Care, Service &
Page 91: Victor Hasselblad AB Box 220, SE -
show all

User Manual - Snap Studios

Create successful ePaper yourself

Delete template?

Save as template?