User Manual - Snap Studios

Recommendations

Info

1 3 5 1 3 5 FLASH Red warning triangle and green LED flash symbol to left of viewfinder LCD display. 2 4 Example of viewfinder LCD display showing Flash set to Rear sync as well as ´- 1EV´ exposure compensation. 2 4 FLASH 76 1) Activate the camera and press the FLASH button once. 2) Turn the front control wheel to set the amount of compensation required: • from +3EV through -3EV (amount dependent on ISO setting) • press Clr (AF button) to clear the setting quickly if required. 3) Turn the rear control wheel to set: • normal sync (flash triggered just after the shutter opens) • rear sync (flash triggered just before the shutter closes) • flash measure (with non-TTL flash units or TTL units in <strong>Manual</strong> mode) 4) The grip LCD shows the flash mode - Normal or Rear - in the standard display. 5) When set to Flash Measure, a specific screen requests you to press the AE-L button in order to make a reading. See below for details. Integral flash The integral flash unit features the following specifications: Guide no. 12 Coverage 56º horizontal, 44º vertical Maximum light fall-off at side centres - 1EV (50%) Colour temperature (full flash) 5,000 – 5,600º K To raise the flash unit into its operative position, slide the flash-unit catch backwards in the direction of the flash symbol. To return the flash unit into its closed position, push down on the top of the unit until it clicks back into place. The flash unit is automatically activated when it is in the operative position and de-activated when returned to its stored position. The green LED flash symbol blinks in the viewfinder when the flash unit is charging and remains stationary when fully charged. The flash output can also be adjusted for optimum light balance in fill-flash situations. Do not use the integral flash together when another external TTL flash unit is connected (and used in TTL or A mode) For full coverage with the integral flash, use 80 mm or longer lenses (without a lens shade). Using the integral flash: 1) Slide the flash-unit catch backwards in the direction of the flash symbol. 2) Press the FLASH button. 3) Choose between Normal or Rear sync by turning the rear control wheel and the amount of compensation (if required) by turning the front control wheel. 4) Press Save (Drive ) button. Make an exposure. 5) If the settings were incorrect to match the output of the flash unit, the viewfinder LCD displays a red triangle alongside a flashing green ‘flash’ symbol plus a warning message - ‘Low flash’. The grip LCD will also display a warning message - ‘Low flash’. Conventional measures should then be taken to correct the situation. (That is: move closer to the main subject, use a larger aperture setting or use a faster film / higher ISO setting).
1 3 5 FLASH AE-L 2 4 6 77 Separate flash unit connection and use Separate flash units can be electrically connected either by way of the hot shoe accessory holder (see previous warnings) on the top of the viewfinder or via a cord to the PC connection port on the left hand side of the camera body. Slave unit switches/ transmitters can also be connected similarly dependant on unit (see specific user manuals for details). Keep the plastic safety cover in place in the hot shoe when not in use. Flash measure of separate flash unit You can measure the effect of an attached flash unit (with PC connected flash units and SCA3902 compatible flash units set to M mode), where the camera acts much as a flash meter would. By choosing ‘Flash measure’, a trial exposure is made with the auxiliary shutter still in place which therefore prevents film frames from being used. The aperture setting can be adjusted and more trial exposures made until the information on the grip LCD is satisfactory. To use flash measure: 1) Press the FLASH button on the grip to access the flash option screen. 2) Turn the rear control wheel until Flash measure appears. 3) Press Save (DRIVE button) to access the flash exposure screen. 4) Make preliminary required aperture setting by turning the front control wheel. 5) Press the AE-L button. The camera will close the aperture, raise the mirror and fire the flash. Light reflected from the flash lit subject will be reflected off a white spot on the auxiliary shutter to the meter sensor. 6) Deviations from a normal exposure are displayed as differences in EV on the grip LCD and the viewfinder LCD. If ‘high’ or ‘low’ appears, change the aperture accordingly and make a new test reading. Change the aperture until Diff EV: 0 appears, or the desired amount of deviation from the normal exposure. Diff EV: Low signifies more than 2 EV under Diff EV: High signifies more than 2 EV over
Page 1 and 2:
1 User Manual (Manual (V1/English)
Page 3 and 4:
Congratulations! Welcome to the fla
Page 5 and 6:
What’s in the box Your new Hassel
Page 7 and 8:
1 Quick Start This section is a qui
Page 9 and 10:
13 14 15 16 17 18 19 20 21 22 B A 2
Page 11 and 12:
33 35 34 36 11 33. From the inactiv
Page 13 and 14:
2 Function Control & Display ■ LC
Page 15 and 16:
Grip LCD Typical camera grip displa
Page 17 and 18:
Viewfinder LCD Typical viewfinder d
Page 19 and 20:
A B C D E I F G H Shutter release b
Page 21 and 22:
P Q R There are also two control bu
Page 23 and 24:
1 3 5 7 1 2 2 4 6 8 23 Carrying str
Page 25 and 26: 9 10 25 • Long-term storage of ba
Page 27 and 28: 4 Viewfinder ■ Multi-mode light m
Page 29 and 30: 5 Lenses ■ Rapid and accurate aut
Page 31 and 32: 10 11 12 7 8 9 Lens focus setting t
Page 33 and 34: 6 Film Magazines ■ Automatic 120/
Page 35 and 36: G H I K L J 35 a time-out of five s
Page 37 and 38: A B 1 2 3 4 5 Film speed Film lengt
Page 39 and 40: 1 2 4 3 5 1 1 2 2 39 Film loading T
Page 41 and 42: 41 Hasselblad provides a number of
Page 43 and 44: Approval Architecture (IAA), an enh
Page 45 and 46: Average (45 x 37 mm) ≈ 70% Centre
Page 47 and 48: 4 1 EXP 2 3 47 A ‘+ 0.3’ abo
Page 49 and 50: 1 3 5 A B +/- 2 4 49 Alternativ
Page 51 and 52: Power The camera can be set at two
Page 53 and 54: 1 AF 2 3 53 Continuous At Contin
Page 55 and 56: 1 2 3 4 5 ON.OFF (PROFILES/
Page 57 and 58: 10 Advanced Features ■ Programmab
Page 59 and 60: There are a number of more advanced
Page 61 and 62: 2 Bracketing 61 Bracketing options
Page 63 and 64: 1 2 3 4 5 6 Number of exposures hig
Page 65 and 66: Standby timeout 1 • 5s • 10s
Page 67 and 68: AE lock / Quick adjust 22 • Exp r
Page 69 and 70: 1 2 5 6 7 3 4 69 Image
Page 71 and 72: 2 4 5 AF Sel. 1 2 3 4 5 6 7 3
Page 73 and 74: 1 3 5 7 2 4 6 73 4.4 Syst
Page 75: The H2 can be used together with mo
Page 79 and 80: There are a number of optional acce
Page 81 and 82: Glossary of Terms For the sake of c
Page 83 and 84: True exposure Shutter position Open
Page 85 and 86: Technical specifications Camera Typ
Page 87 and 88: External dimensions approx. 155 mm
Page 89 and 90: Problems, Equipment Care, Service &
Page 91: Victor Hasselblad AB Box 220, SE -
show all

User Manual - Snap Studios

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?