User Manual - Snap Studios

Recommendations

Info

1 2 1 2 1 2 3 4 5 6 7 8 9 10 11 12 2 1 8 H2-Kit only / H2- Separate items If your new H2 was supplied in kit form, you will only need to insert the camera batteries to make it useable immediately. After completing steps 1- 4, you can go straight to 6-7 and 9-10 (marked in red) and then directly to the section after step 17 to activate the camera. (Please note: if you want to use a rechargeable battery pack immediately, please see separate instructions under the ‘Camera Body’ heading for use and then go straight to step 4). If, however, the equipment was supplied as separate items, you will need to follow the whole sequence for full assembly and use. 1. Remove the battery holder from the grip by depressing the battery holder button and simultaneously swinging the battery holder retaining lever down until it stops. Pull battery holder downwards. 2. Depress the red button on the battery holder until the battery cassette is released. Withdraw the cassette from the holder. 3. Load three CR-123 Lithium batteries into the cassette, ensuring the polarity of each battery is correctly oriented (see the ‘+’ markings on the cassette). Re-insert the cassette into the battery holder, ensuring the red button clicks back into its retaining position. 4. Holding the battery holder flat against the grip and aligning the two upper lugs with the slot in the grip, slide it back into position as far as it will go. Swing back the battery holder retaining lever until it clicks back into place. 5. Remove the front protective cover from the camera body by keeping the lens release button depressed and rotating the cover counter-clockwise until it is released. 6. Remove the lens shade by turning it clockwise. 7. Remove the rear lens cap by unscrewing it in a counterclockwise direction. 8. Attach the lens to the camera body by firstly aligning the red index on the lens mount with the red index on the camera mount. Grip the lens by the metal barrel (not the rubber focusing ring) and turn it approximately one quarter turn clockwise until it clicks into place. 9. Remove the front lens cap by pinching together the two retaining clips. 10. Attach lens shade to lens by aligning the indexes and turning the shade clockwise a quarter turn. 11. Remove the rear protective cover from the camera body by pushing the magazine retaining latch to the right and inwards simultaneously. If you decide to attach a digital back instead of a film magazine at this point, please check with the appropriate user manual for details. 12. Remove the protective cover from the film magazine by placing your thumb on the upper recess and pulling the top of the cover away from the magazine. Push downwards on the cover to release the lower catch on the cover from the magazine retaining bar.
13 14 15 16 17 18 19 20 21 22 B A 2 1 9 13. Rest the magazine retention groove on the magazine support on the camera body ensuring that they are correctly positioned. 14. Swing the magazine towards the camera body and firmly press into place with a click. If there is resistance, the magazine retaining hook has probably been inadvertently released. Push the magazine retaining latch to the right and inwards simultaneously again to reset it. 15. Remove the top protective cover from the viewfinder screen location by lifting a corner. 16. Remove the protective cover from the viewfinder by depressing the viewfinder release button. 17. While holding the viewfinder at a slight angle, locate the front section into place on the front edge of the viewfinder screen recess in the camera body ensuring the central locating lug and databus interface are positioned correctly. Swing the viewfinder downwards and press firmly until it clicks into place. Ensure that both sides of the viewfinder are seated correctly. 18. Point the camera at a smooth toned area. Turn the eyesight adjustment dial until you achieve optimum sharpness of the markings on the viewfinder screen. .......................................................................... The camera is now complete. If you press the ON.OFF button A for half a second, the camera will activate. If the camera enters STANDBY mode (the LCD screen will show the H2 symbol only), reactivate it by pressing the shutter release button B halfway (or the ON.OFF button). You can now explore the menus, buttons, control wheels, etc observing the changes on the LCD on the grip as well as the LCD in the viewfinder. film loading ... 19. Fold out the film holder key. 20. Turn the key counter-clockwise 90° and withdraw the film holder completely. (Remove the protective slip from the internal battery compartment if necessary) 21. Place an empty take-up spool in the upper spool holder by pushing one end of the spool against the sprung spool retaining arm to engage the stud in the spool end. Position the other end of the spool over the fixed stud in the holder. Rotate the spool a little if necessary until clicks into position. 22. Completely remove the retaining paper band from a new roll of film and place it in the lower spool holder in the same manner as the empty spool. Ensure you do not place the new film spool the wrong way around! See diagram for correct orientation.
Page 1 and 2: 1 User Manual (Manual (V1/English)
Page 3 and 4: Congratulations! Welcome to the fla
Page 5 and 6: What’s in the box Your new Hassel
Page 7: 1 Quick Start This section is a qui
Page 11 and 12: 33 35 34 36 11 33. From the inactiv
Page 13 and 14: 2 Function Control & Display ■ LC
Page 15 and 16: Grip LCD Typical camera grip displa
Page 17 and 18: Viewfinder LCD Typical viewfinder d
Page 19 and 20: A B C D E I F G H Shutter release b
Page 21 and 22: P Q R There are also two control bu
Page 23 and 24: 1 3 5 7 1 2 2 4 6 8 23 Carrying str
Page 25 and 26: 9 10 25 • Long-term storage of ba
Page 27 and 28: 4 Viewfinder ■ Multi-mode light m
Page 29 and 30: 5 Lenses ■ Rapid and accurate aut
Page 31 and 32: 10 11 12 7 8 9 Lens focus setting t
Page 33 and 34: 6 Film Magazines ■ Automatic 120/
Page 35 and 36: G H I K L J 35 a time-out of five s
Page 37 and 38: A B 1 2 3 4 5 Film speed Film lengt
Page 39 and 40: 1 2 4 3 5 1 1 2 2 39 Film loading T
Page 41 and 42: 41 Hasselblad provides a number of
Page 43 and 44: Approval Architecture (IAA), an enh
Page 45 and 46: Average (45 x 37 mm) ≈ 70% Centre
Page 47 and 48: 4 1 EXP 2 3 47 A ‘+ 0.3’ abo
Page 49 and 50: 1 3 5 A B +/- 2 4 49 Alternativ
Page 51 and 52: Power The camera can be set at two
Page 53 and 54: 1 AF 2 3 53 Continuous At Contin
Page 55 and 56: 1 2 3 4 5 ON.OFF (PROFILES/
Page 57 and 58: 10 Advanced Features ■ Programmab
Page 59 and 60:
There are a number of more advanced
Page 61 and 62:
2 Bracketing 61 Bracketing options
Page 63 and 64:
1 2 3 4 5 6 Number of exposures hig
Page 65 and 66:
Standby timeout 1 • 5s • 10s
Page 67 and 68:
AE lock / Quick adjust 22 • Exp r
Page 69 and 70:
1 2 5 6 7 3 4 69 Image
Page 71 and 72:
2 4 5 AF Sel. 1 2 3 4 5 6 7 3
Page 73 and 74:
1 3 5 7 2 4 6 73 4.4 Syst
Page 75 and 76:
The H2 can be used together with mo
Page 77 and 78:
1 3 5 FLASH AE-L 2 4 6 77 Sepa
Page 79 and 80:
There are a number of optional acce
Page 81 and 82:
Glossary of Terms For the sake of c
Page 83 and 84:
True exposure Shutter position Open
Page 85 and 86:
Technical specifications Camera Typ
Page 87 and 88:
External dimensions approx. 155 mm
Page 89 and 90:
Problems, Equipment Care, Service &
Page 91:
Victor Hasselblad AB Box 220, SE -
show all

User Manual - Snap Studios

Create successful ePaper yourself

Delete template?

Save as template?