UD-35 SERVICE UPDATE FIRST HALF—2009 - Whirlpool

More documents

Recommendations

Info

January 2008, started production of Jenn-Air BIR models in Ft Smith, AR. with the KitchenAid model line. BIR MODEL REFRESH Ft. Smith, AR produced models, starting July ‘08 Model Number Serial Number 38
Original Large Reservoir Dispenser drip KABIR <strong>UPDATE</strong> -2009 ICE AND WATER <strong>UPDATE</strong> 2327509 Verify the 2327509 tank is installed. This is the smaller baffle tank. See figure 1. Verify the inlet and outlet is installed correctly from the reservoir tank. The correct inlet and outlet connections are Critical to ensure dispenser dripping is minimized. The 2314271 with 5/16” check valve has been helpful at both the door union (Tline models) and tapped into the line right after the reservoir outlet connection. Removing the ARD on the M line will help. Use regular ¼ tubing. You will need a bracket at the top in the dispenser to hold the tube. The water reservoir tank, 2327509, has dramatically reduced our dispenser drip calls. Make sure the technicians are using this smaller baffle tank as a service part, not the larger baffle tank. The larger baffle tank does not improve dispenser drip as well as the 2327509 tank does. 39 Inlet Figure 1 ICE CUBES STICKING TOGETHER Infrequent Use Outlet Ice cubes will stick together over time. Customers that dispense ice infrequently (more than a week or so between dispensing) will notice this because it is normal. This is probably the most common cause of cube clumping complaints. Look for cubes which otherwise appear fairly normal (although over long periods of time some frost may build). Sublimation and melting occur at the molecular level even at temperatures which remain well below freezing. The water molecules condense and refreeze back on the cubes and this will cause cubes to freeze together at points of contact. The main points to take away from this are: Neither warm temperatures nor airflow are necessary for ice cubes to stick together. Over time, this will occur even at extremely cold temperatures. The cause is that molecules of water (ice) on adjacent cubes of ice join into the same ice crystal at the point of contact. The size and strength of the bonds grow with time. It begins happening immediately, but is at first too weak to notice. Use of the dispenser drives an auger motor which breaks up bonds, at least until they have grown too strong.
Page 1 and 2: SERVICE UPDATE FIRST HALF—2009 Ho
Page 3 and 4: TABLE OF CONTENTS COOKING .........
Page 5 and 6: TABLE OF CONTENTS Main User Interfa
Page 7 and 8: COOKING UPDATES KITCHENAID FREESTAN
Page 9 and 10: COOKING UPDATES KITCHENAID FREESTAN
Page 11 and 12: COOKING UPDATES WARMING DRAWER FEAT
Page 13 and 14: LAUNDRY PRODUCT UPDATES STEAM WASHE
Page 15 and 16: STEAM WASHER CHANGES (continued) CC
Page 17 and 18: FRONT LOAD WASHERS FAILURE CODES ON
Page 19 and 20: “SPORT” BELLOW A “softer” b
Page 21 and 22: SQUEAKING NOISE DURING SPIN Make a
Page 23 and 24: AIR TRAP The air trap may be rattli
Page 25 and 26: PROPER LOADING Proper loading of wa
Page 27 and 28: TIER III The new Tier III washers b
Page 29 and 30: PRESSURE SWITCH VS PRESSURE SENSORS
Page 31 and 32: DRYERS FL FAILURE CODES CHANGING In
Page 33 and 34: RAST CONNECTOR Care needs to be tak
Page 35 and 36: CLEAN UP UPDATES HOT WATER DISPENSE
Page 37 and 38: SILVERWARE ZONE (continued) It will
Page 39 and 40: DISH DRAWER DOOR ALIGNMENT Units dr
Page 41 and 42: - NOTES -
Page 43: KSSC42QMS03, starting December 2006
Page 47 and 48: ICE AND WATER UPDATE -cont. Shorten
Page 49 and 50: IN DOOR ICE DIAGNOSTICS The next th
Page 51 and 52: IN DOOR ICE DIAGNOSTICS (continued)
Page 53 and 54: EMITTER & RECEIVER ISSUES (BOTTOM M
Page 55 and 56: CABINET & DOOR ISSUES DOORS OUT OF
Page 57 and 58: TO INSTALL SHIM BEHIND RC BOTTOM HI
Page 59 and 60: MISALIGNED FREEZER DRAWER (continue
Page 61 and 62: LIGHT SWITCH PAD (36BM and 42FDBM O
Page 63 and 64: SMALL GAP BETWEEN UI AND FC DOOR Sm
Page 65 and 66: MAIN CONTROL The Gemini ES is the m
Page 67 and 68: DISPENSER CONTROL The Niagara board
Page 69 and 70: AVERAGE CRISPER TEMPERATURES KABI S
Page 71 and 72: • • • INTERMITTENT OVER TEMPE
Page 73 and 74: Old Cover Drain pan Overflows Model
Page 75 and 76: • • • • • PERFORMANCE UPD
Page 77 and 78: BOTTOM MOUNT SEALED SYSTEM JOINT LO
Page 79 and 80: • • • MAIN USER INTERFACE Not
Page 81 and 82: Component Description FC Thermistor
Page 83 and 84: Compressor Inverter COMPONENT TESTI
Page 85 and 86: AIR DOOR During operation (diagnost
Page 87 and 88: SERVICE POINTER INDEX COOKING BRAND
Page 89 and 90: COOKING (continued) BRAND & ID# DES
Page 91 and 92: BRAND & ID# DESCRIPTION DATE ISSUED
Page 93 and 94: - NOTES - 87

UD-35 SERVICE UPDATE FIRST HALF—2009 - Whirlpool

Create successful ePaper yourself

Delete template?

Save as template?