UD-35 SERVICE UPDATE FIRST HALF—2009 - Whirlpool

More documents

Recommendations

Info

TO INSTALL SHIM BEHIND RC BOTTOM HINGE (cont.) With the door removed, peel off the Hinge cover, remove the 4 hinge screws. Be very careful not to round out the screw head if using a power screwdriver. Replace hinge after adding 1.5mm (p/n 2207470) shim behind it. Replace hinge cover, may need 2 sided tape if adhesive is no longer sticky. Check to make sure top hinge does not need to now be adjusted out (Loosen Tap Plate). Check door seal. Hinge Cover BIR BOTTOM MOUNT FREEZER DRAWER MISALIGNMENT Condition : Drawer is not level (i.e. one side is higher than other) 52 Hinge Screws
MISALIGNED FREEZER DRAWER (continued) Always check product levelness, do not reference FC drawer off RC door in case RC door is sagging or the issue. RC door is easier to adjust. If product is Overlay, check door alignment with panel off, make sure panel is not the issue. Tighten all screws; bolts connecting drawer to basket, see figure 1, screws connecting basket to slides, see figure 2 and bolts connecting slide brackets to the product, see figure 3. Condition: Top/Bottom of drawer is tilted out or drawer is not sealing across the top or bottom. Loosen top drawer to basket bolts and remove the bottom bolts on each side. See figure 4. There are 2 adjustment holes to use to reposition the lower bolts. See figure 5. Tilt the door in the direction it needs to go, and re-insert the bottom bolts in the corresponding holes to change the drawer angle. Figure 4 Drawer to Basket Bolts Figure 1 Basket to Slide Screws Figure 2 53 Slide Bracket to Liner Screws Figure 3 Adjustment Holes Figure 5
Page 1 and 2:
SERVICE UPDATE FIRST HALF—2009 Ho
Page 3 and 4:
TABLE OF CONTENTS COOKING .........
Page 5 and 6:
TABLE OF CONTENTS Main User Interfa
Page 7 and 8: COOKING UPDATES KITCHENAID FREESTAN
Page 9 and 10: COOKING UPDATES KITCHENAID FREESTAN
Page 11 and 12: COOKING UPDATES WARMING DRAWER FEAT
Page 13 and 14: LAUNDRY PRODUCT UPDATES STEAM WASHE
Page 15 and 16: STEAM WASHER CHANGES (continued) CC
Page 17 and 18: FRONT LOAD WASHERS FAILURE CODES ON
Page 19 and 20: “SPORT” BELLOW A “softer” b
Page 21 and 22: SQUEAKING NOISE DURING SPIN Make a
Page 23 and 24: AIR TRAP The air trap may be rattli
Page 25 and 26: PROPER LOADING Proper loading of wa
Page 27 and 28: TIER III The new Tier III washers b
Page 29 and 30: PRESSURE SWITCH VS PRESSURE SENSORS
Page 31 and 32: DRYERS FL FAILURE CODES CHANGING In
Page 33 and 34: RAST CONNECTOR Care needs to be tak
Page 35 and 36: CLEAN UP UPDATES HOT WATER DISPENSE
Page 37 and 38: SILVERWARE ZONE (continued) It will
Page 39 and 40: DISH DRAWER DOOR ALIGNMENT Units dr
Page 41 and 42: - NOTES -
Page 43 and 44: KSSC42QMS03, starting December 2006
Page 45 and 46: Original Large Reservoir Dispenser
Page 47 and 48: ICE AND WATER UPDATE -cont. Shorten
Page 49 and 50: IN DOOR ICE DIAGNOSTICS The next th
Page 51 and 52: IN DOOR ICE DIAGNOSTICS (continued)
Page 53 and 54: EMITTER & RECEIVER ISSUES (BOTTOM M
Page 55 and 56: CABINET & DOOR ISSUES DOORS OUT OF
Page 57: TO INSTALL SHIM BEHIND RC BOTTOM HI
Page 61 and 62: LIGHT SWITCH PAD (36BM and 42FDBM O
Page 63 and 64: SMALL GAP BETWEEN UI AND FC DOOR Sm
Page 65 and 66: MAIN CONTROL The Gemini ES is the m
Page 67 and 68: DISPENSER CONTROL The Niagara board
Page 69 and 70: AVERAGE CRISPER TEMPERATURES KABI S
Page 71 and 72: • • • INTERMITTENT OVER TEMPE
Page 73 and 74: Old Cover Drain pan Overflows Model
Page 75 and 76: • • • • • PERFORMANCE UPD
Page 77 and 78: BOTTOM MOUNT SEALED SYSTEM JOINT LO
Page 79 and 80: • • • MAIN USER INTERFACE Not
Page 81 and 82: Component Description FC Thermistor
Page 83 and 84: Compressor Inverter COMPONENT TESTI
Page 85 and 86: AIR DOOR During operation (diagnost
Page 87 and 88: SERVICE POINTER INDEX COOKING BRAND
Page 89 and 90: COOKING (continued) BRAND & ID# DES
Page 91 and 92: BRAND & ID# DESCRIPTION DATE ISSUED
Page 93 and 94: - NOTES - 87
show all

UD-35 SERVICE UPDATE FIRST HALF—2009 - Whirlpool

Create successful ePaper yourself

Delete template?

Save as template?