UD-35 SERVICE UPDATE FIRST HALF—2009 - Whirlpool

More documents

Recommendations

Info

FROST BUILD UP - DISPENSER DOOR NOT CLOSING This unit was exchanged as being non repairable. If you are experiencing a “ice door not sealing condition, Examine this area to insure the dispenser wires are not in the way of the ice flapper door. A new part has been added at production to prevent this this issue from from occurring. PEX PEX Unit – Deemed Not repairable. repairable. The unit could have been easily easily repaired. No Seal Good Seal No Seal Good Seal To verify the ice door seal, press the ice flapper door against the ice chute to make an impression into the seal. Remove the flapper door. If you see an impression across all four sides of the ice chute, you have a good seal. 48
CABINET & DOOR ISSUES DOORS OUT OF ALIGNMENT –SXS & FDBM Condition: Doors are not aligned at top, RC or FC door is higher. RC is pre-set to be 1.5mm higher than FC at factory, under assumption food load will level them out. • Service Fix: -Check door gaps between RC and FC at top and bottom. If door out of align and gaps are uneven, loosen hinge screws for door that is lower, pull top of door toward hinge and hold as you re-tighten the hinge screws. See figure 1 -If gaps are even or parallel, take clip off of bottom hinge bushing and use wrench to raise and lower door height. A combination of raising one door and lowering another should be enough to fix most door alignment issue. Be sure to check door seal after adjustment. See figure 2 Figure 1 CAB/DOOR ADJUSTMENT RANGE 49 Clip Figure 2 Right to left – Each door has 10mm, (.4 inches) of total movement right to left. However, this varies the height by 3mm. There should be a gap of approx. 6mm, (.2 inches) between doors. The top hinge has enough right movement to move too far to the right causing light switch arm to hit side trim, so always check for interference when done adjusting. No left right movement in bottom hinge. Up and down – The bushing on the bottom hinge allows for 10mm, (.4 inches) of adjustment. In and out – Top hinge tap plate allows for 5.5mm, (.2 inches) of in and out movement. No bottom hinge movement.
Page 1 and 2:
SERVICE UPDATE FIRST HALF—2009 Ho
Page 3 and 4: TABLE OF CONTENTS COOKING .........
Page 5 and 6: TABLE OF CONTENTS Main User Interfa
Page 7 and 8: COOKING UPDATES KITCHENAID FREESTAN
Page 9 and 10: COOKING UPDATES KITCHENAID FREESTAN
Page 11 and 12: COOKING UPDATES WARMING DRAWER FEAT
Page 13 and 14: LAUNDRY PRODUCT UPDATES STEAM WASHE
Page 15 and 16: STEAM WASHER CHANGES (continued) CC
Page 17 and 18: FRONT LOAD WASHERS FAILURE CODES ON
Page 19 and 20: “SPORT” BELLOW A “softer” b
Page 21 and 22: SQUEAKING NOISE DURING SPIN Make a
Page 23 and 24: AIR TRAP The air trap may be rattli
Page 25 and 26: PROPER LOADING Proper loading of wa
Page 27 and 28: TIER III The new Tier III washers b
Page 29 and 30: PRESSURE SWITCH VS PRESSURE SENSORS
Page 31 and 32: DRYERS FL FAILURE CODES CHANGING In
Page 33 and 34: RAST CONNECTOR Care needs to be tak
Page 35 and 36: CLEAN UP UPDATES HOT WATER DISPENSE
Page 37 and 38: SILVERWARE ZONE (continued) It will
Page 39 and 40: DISH DRAWER DOOR ALIGNMENT Units dr
Page 41 and 42: - NOTES -
Page 43 and 44: KSSC42QMS03, starting December 2006
Page 45 and 46: Original Large Reservoir Dispenser
Page 47 and 48: ICE AND WATER UPDATE -cont. Shorten
Page 49 and 50: IN DOOR ICE DIAGNOSTICS The next th
Page 51 and 52: IN DOOR ICE DIAGNOSTICS (continued)
Page 53: EMITTER & RECEIVER ISSUES (BOTTOM M
Page 57 and 58: TO INSTALL SHIM BEHIND RC BOTTOM HI
Page 59 and 60: MISALIGNED FREEZER DRAWER (continue
Page 61 and 62: LIGHT SWITCH PAD (36BM and 42FDBM O
Page 63 and 64: SMALL GAP BETWEEN UI AND FC DOOR Sm
Page 65 and 66: MAIN CONTROL The Gemini ES is the m
Page 67 and 68: DISPENSER CONTROL The Niagara board
Page 69 and 70: AVERAGE CRISPER TEMPERATURES KABI S
Page 71 and 72: • • • INTERMITTENT OVER TEMPE
Page 73 and 74: Old Cover Drain pan Overflows Model
Page 75 and 76: • • • • • PERFORMANCE UPD
Page 77 and 78: BOTTOM MOUNT SEALED SYSTEM JOINT LO
Page 79 and 80: • • • MAIN USER INTERFACE Not
Page 81 and 82: Component Description FC Thermistor
Page 83 and 84: Compressor Inverter COMPONENT TESTI
Page 85 and 86: AIR DOOR During operation (diagnost
Page 87 and 88: SERVICE POINTER INDEX COOKING BRAND
Page 89 and 90: COOKING (continued) BRAND & ID# DES
Page 91 and 92: BRAND & ID# DESCRIPTION DATE ISSUED
Page 93 and 94: - NOTES - 87
show all

UD-35 SERVICE UPDATE FIRST HALF—2009 - Whirlpool

Create successful ePaper yourself

Delete template?

Save as template?