English - StellarSupport - John Deere

More documents

Recommendations

Info

Installation in Most GreenStar Ready Machines A—Corner Post Mounts B—Wing Nuts (2 Used) C—Vehicle Display Connector D—Connector on Display 1. Turn OFF vehicle. 2. Attach bracket to corner post mounts (A). 3. Attach display to bracket using the wing nuts (B) (provided with display). Installation 20-1 4. Attach harness to the corner post connector (C) and the lower connector on the back of the display (D). 5. Position the display so that it is comfortable to reach and does not obstruct your view. IMPORTANT: Display must be connected to SWITCHED and CONSTANT power. This allows the display to shutdown properly and save data. When the key is switched off, a ’Saving Settings’ message should appear on the screen. NOTE: Bracket and harness are sold separately. Uses the same brackets and harnesses as GS2 displays. OUO6050,000128E -19-19JUL10-1/1 112912 PN=18
Power Up During power up of display, a start-up screen will show a status bar that indicates display is powering up. Once the display has powered up, if no implement is connected, a default performance monitor screen will be shown. If an ISO implement is connected, that implement's information will be shown in application info area along with ten softkeys. A—Stop B—Accessories C—Run D—Start Installation Ignition Switch Display Power Up/Power Down Current Next Key Switch Position Engine Action Display and Tractor Description Key Switch Position Controllers STOP ACCESSORIES No Start No Start Display and engine do not start, but can be used to run other machine accessories. STOP RUN No Start Start It is acceptable to start the display in this manner ONLY IF operator turns the key back to STOP position to turn off the display and let it fully power down and save settings before starting the engine. STOP START Start Start Proper way to start the display if operator plans on starting the engine. RUN START Start Potentially Have Issues Do not follow this scenario with machine and display or data loss can occur. If display is already powered up when the key is turned to the START position, it could create issues with display memory and connectivity with controllers. Starting the engine causes a drop in current, which can restart controllers in the wrong order as well as cause sudden data loss on the display. ALWAYS allow the display to shut down properly by turning the key to the STOP position before starting the engine. RUN STOP Turn Off, if Running Turn Off Proper way to turn off the engine and display OR for allowing the display to power down properly if the engine was not running and you plan to start it. START RUN Running Stay On The key switch only remains in START position as long as the operator is turning it. IMPORTANT: Do not remove 12 V power from display until the LED light is black. Prematurely removing power (green or orange light status) may cause loss of data and/or the display to lose functionality. It may take up to 20 seconds after removing key power for the LED light to completely go black. IMPORTANT: The display must always be allowed to completely power down (LED light turns off) whenever the key is placed in the STOP position. Failure to do so can result in lost or corrupted data when power is restored. When setting up the display with vehicle key in the accessory position (power on, 20-2 engine off), turn key to STOP position for 20 seconds BEFORE starting the vehicle. This ensures the setup data is saved to the internal memory before operating. If the vehicle is running during setup and programming, turn the vehicle off with key in the STOP position and wait 30 seconds before restarting. This ensures that all data is saved to the internal memory. DO NOT turn the key to the start position directly from the accessory position. The reduction in voltage during the starting phase could result in a loss of all setup data. Continued on next page RW00482,00000B8 -19-26NOV12-1/2 PC16120 —UN—25OCT12 112912 PN=19
Page 1 and 2: 2630 GreenStar Display *OMPFP12635*
Page 3 and 4: Contents Page Safety Recognize Safe
Page 5 and 6: Page Understanding Section Control
Page 7 and 8: Recognize Safety Information This i
Page 9 and 10: Operate Guidance Systems Safely Do
Page 11 and 12: Implement Detected Warning This mes
Page 13 and 14: Theory of Operation IMPORTANT: It i
Page 15 and 16: Back of Display Backside of Display
Page 17: Screen Layout A—Home B—Menu C
Page 21 and 22: View Multiple Display Settings 1. M
Page 23 and 24: Input Fields Input Fields There are
Page 25 and 26: Display Software Activations The di
Page 27 and 28: DISPLAY softkey When display is ini
Page 29 and 30: NOTE: Highlight color is defaulted
Page 31 and 32: The Advance Display Settings button
Page 33 and 34: Calculator The display has a standa
Page 35 and 36: Press softkey A, then press the lar
Page 37 and 38: Layout Manager Option H Layout Mana
Page 39 and 40: License Agreement The first time yo
Page 41 and 42: EQUIPMENT softkey The equipment scr
Page 43 and 44: Machine Setup MENU >> GREENSTAR 3 P
Page 45 and 46: NOTE: Machine Turn Radius and Turni
Page 47 and 48: A—Machine Tab B—Implement 1 Tab
Page 49 and 50: Track Spacing A—m (ft)/(rows) but
Page 51 and 52: Implement 2 and Implement 3 tab A
Page 53 and 54: Field Locator With external boundar
Page 55 and 56: Map View Toggle - The map can be to
Page 57 and 58: Map Settings button (A) - This butt
Page 59 and 60: Boundaries Tab Select MENU > GREENS
Page 61 and 62: Delete and Rename Boundaries Along
Page 63 and 64: 6. Choose whether the boundary will
Page 65 and 66: A—Maps Tab B—Boundaries Tab C
Page 67 and 68: Constant Offset Boundary NOTE: A bo
Page 69 and 70:
Read This Manual Before attempting
Page 71 and 72:
VIEW tab A—View tab B—Guidance
Page 73 and 74:
AutoTrac Status Pie Allows AutoTrac
Page 75 and 76:
Moving Map view and Perspective Vie
Page 77 and 78:
Coverage Maps Select the foreground
Page 79 and 80:
Predicting Turn Points Guidance To
Page 81 and 82:
Lead Compensation NOTE: This featur
Page 83 and 84:
SHIFT TRACK SETTINGS tab SHIFT TRAC
Page 85 and 86:
StarFire Signal Monitoring System T
Page 87 and 88:
Track 0 Setup Set Tracking Mode (E)
Page 89 and 90:
• Set track spacing from EQUIPMEN
Page 91 and 92:
A + Heading 1. Drive to desired loc
Page 93 and 94:
Guidance Line Calculation Guidance
Page 95 and 96:
Track 0 Setup A—View B—Guidance
Page 97 and 98:
Repeat Mode A—View B—Guidance S
Page 99 and 100:
Smooth Tight Turns GreenStar 3 Pro
Page 101 and 102:
Operating Curve Track IMPORTANT: RT
Page 103 and 104:
Record and Repeat This feature allo
Page 105 and 106:
Guidance Patterns The method of sea
Page 107 and 108:
Recording a Straight Path within a
Page 109 and 110:
AB Curve Mode Theory of Operation A
Page 111 and 112:
Setup Guidance GreenStar 3 Pro - Gu
Page 113 and 114:
NOTE: If GPS signal is lost while r
Page 115 and 116:
Smooth Tight Turns GreenStar 3 Pro
Page 117 and 118:
Circle Track Mode Track 0 Setup A
Page 119 and 120:
NOTE: It is required to drive over
Page 121 and 122:
In operating Circle Track in some s
Page 123 and 124:
8. The Current Track is displayed a
Page 125 and 126:
3. Check the Tram Lines Checkbox (A
Page 127 and 128:
AutoTrac Setup Operate Guidance Sys
Page 129 and 130:
Tractors 4700 and 4710 Sprayers Res
Page 131 and 132:
Adjusting Steering Sensitivity Leve
Page 133 and 134:
• Steering Sensitivity—Set at 1
Page 135 and 136:
Heading Error Meter The Heading Err
Page 137 and 138:
Advanced AutoTrac Settings Select m
Page 139 and 140:
Optimizing AutoTrac Controller Perf
Page 141 and 142:
Acquire Sensitivity Determines how
Page 143 and 144:
Enhanced AutoTrac Diagnostics • (
Page 145 and 146:
AutoTrac System Accuracy Accuracy E
Page 147 and 148:
AutoTrac Tractors Enabling System T
Page 149 and 150:
AutoTrac Sprayers Enabling System P
Page 151 and 152:
AutoTrac Resume Button (If Equipped
Page 153 and 154:
AutoTrac Self-Propelled Forage Harv
Page 155 and 156:
Compatible Systems Press: MENU butt
Page 157 and 158:
UPM (UNIVERSAL PERFORMANCE MONITOR)
Page 159 and 160:
SETTINGS SCREEN The setup screen of
Page 161 and 162:
Implement Switch Open This item is
Page 163 and 164:
PERFORMANCE MONITOR CALIBRATIONS Pe
Page 165 and 166:
Calibrating Dual Beam Radar 1. Sele
Page 167 and 168:
6. Address 60 should display 57.42
Page 169 and 170:
Total Engine Hours Engine hours are
Page 171 and 172:
Drop down menus for APM selectable
Page 173 and 174:
No GPS Documentation If GPS is lost
Page 175 and 176:
Client, Farm, Field, and Task Setup
Page 177 and 178:
Limited Availability of Operations
Page 179 and 180:
A—Choose Seed Type B—Displays P
Page 181 and 182:
Assign Varieties to Rows The operat
Page 183 and 184:
Select the target rate box (B) and
Page 185 and 186:
Using Documentation with Seeder/Air
Page 187 and 188:
Assign Variety to Tank For tanks co
Page 189 and 190:
NOTE: Max. 25 entries could be adde
Page 191 and 192:
Using Documentation with a Dry Box/
Page 193 and 194:
Product Application Product Details
Page 195 and 196:
A—Product Name tab B—New C—Pr
Page 197 and 198:
Viewing Locked Tank Mixes If you cr
Page 199 and 200:
Harvest Documentation Setup MENU bu
Page 201 and 202:
Defining Residue Management Select
Page 203 and 204:
Defining Header Screen: SETUP—HEA
Page 205 and 206:
Yield Units NOTE: See Standard Weig
Page 207 and 208:
Cut Width Adjustment A—Machine B
Page 209 and 210:
Harvest Monitor Yield Calibration C
Page 211 and 212:
Low Flow Compensation Procedure—O
Page 213 and 214:
Moisture Correction NOTE: Harvestin
Page 215 and 216:
Harvest Monitor Cotton Setup Press:
Page 217 and 218:
A—Row #1 B—Row #2 C—Row #3 D
Page 219 and 220:
Harvest Monitor Cotton Calibration
Page 221 and 222:
Standard Calibration Screen: SETUP
Page 223 and 224:
Map Based Prescriptions Prescriptio
Page 225 and 226:
Shapefile Converter The Shapefile C
Page 227 and 228:
Shapefile Conversion Maximum Number
Page 229 and 230:
Simultaneous Documentation/Prescrip
Page 231 and 232:
TOTALS button Totals The Totals pag
Page 233 and 234:
Set Up Totals on Home Page 1. Selec
Page 235 and 236:
3. For Harvest operations, checking
Page 237 and 238:
Overlap Control NOTE: When using Ov
Page 239 and 240:
Adding to an Existing Load The Load
Page 241 and 242:
Viewing Filtered Totals Reports The
Page 243 and 244:
Theory of Operation John Deere Sect
Page 245 and 246:
Required Setup IMPORTANT: Some oper
Page 247 and 248:
View by Operation The View by Opera
Page 249 and 250:
Overlap Settings The system can be
Page 251 and 252:
Section Control Map Settings The Ma
Page 253 and 254:
John Deere Section Control Understa
Page 255 and 256:
A—Rank 1 B—Rank 2 C—System De
Page 257 and 258:
• (A) View drop down box - Indica
Page 259 and 260:
Constant Ground Speed (km/h) Physic
Page 261 and 262:
Constant Ground Speed (mph) Physica
Page 263 and 264:
The John Deere pull-type sprayer pr
Page 265 and 266:
Softkeys 64 Softkeys (VT) VT versio
Page 267 and 268:
Machine type (A) will be set to tra
Page 269 and 270:
“Implement width” in always loa
Page 271 and 272:
Theory of Operation John Deere Remo
Page 273 and 274:
A—Blue Outline B—Wireless Conne
Page 275 and 276:
8. Verify MTG is communicating and
Page 277 and 278:
Auxiliary Control Enabled This mess
Page 279 and 280:
Auxiliary Control Not Available IMP
Page 281 and 282:
Auxiliary Controls Auxiliary Contro
Page 283 and 284:
• A green status indicator (D) in
Page 285 and 286:
Auxiliary Controls—Assignment Err
Page 287 and 288:
Auxiliary Controls—Preferred Assi
Page 289 and 290:
A—View Selection B—Conflicts C
Page 291 and 292:
A—Status Selection B—Enabled Au
Page 293 and 294:
Why Assign the COM Port? The RS232
Page 295 and 296:
Com Port Settings Use this screen t
Page 297 and 298:
2. Review Com Port assignment setti
Page 299 and 300:
Deactivate COM Port IMPORTANT: Each
Page 301 and 302:
YARA N-Sensor NOTE: The YARA N-Sens
Page 303 and 304:
15. Select auto-generated product a
Page 305 and 306:
GPS Settings NOTE: GreenSeeker®is
Page 307 and 308:
10. Select NEW in Profile drop-down
Page 309 and 310:
GreenSeeker® Prescription 18. Sele
Page 311 and 312:
1. Select the Implement Type and Im
Page 313 and 314:
Connecting RS-232 GPS Receivers NOT
Page 315 and 316:
5. Insert harness wires into correc
Page 317 and 318:
Naming Each of the three camera inp
Page 319 and 320:
Theory of Operation Data and setup
Page 321 and 322:
Importing Global or Shapefile Presc
Page 323 and 324:
Example 3 - Transferring Guidance L
Page 325 and 326:
Data Type Details Data Management D
Page 327 and 328:
Alarm - GreenStar Setup Information
Page 329 and 330:
Downloading Software Updates Softwa
Page 331 and 332:
Message Center Troubleshooting and
Page 333 and 334:
Message Center Icons These icons ar
Page 335 and 336:
Device Info and Bus Status When DEV
Page 337 and 338:
Pre-Season Checklist for Guidance I
Page 339 and 340:
A: This is a common error if multip
Page 341 and 342:
Reprogramming Error Codes Troublesh
Page 343 and 344:
Task Controller Alarms Alarm, Task
Page 345 and 346:
Alarm, Task Controller, Invalid Imp
Page 347 and 348:
Address Number Address Name 046 Set
Page 349 and 350:
Trouble Code Pop-Up Boxes—Platfor
Page 351 and 352:
Trouble Code Pop-Up Boxes—Documen
Page 353 and 354:
Guidance Alarms Troubleshooting and
Page 355 and 356:
AutoTrac Deactivation Messages Each
Page 357 and 358:
GreenStar Sytem Component Pinout Ci
Page 359 and 360:
Specifications Toxic or Hazardous S
Page 361 and 362:
Glossary Glossary of Terms Term Mea
Page 363 and 364:
A Index Page AB Curve Track Mode Cr
Page 365 and 366:
Page Tractors......................
Page 367 and 368:
Page Setup.........................
Page 369 and 370:
Page Resetting Display Alerts .....
Page 371 and 372:
Page Track 0 Setup Adaptive Curve T
Page 373 and 374:
Technical Information John Deere Se
Page 375 and 376:
John Deere Parts John Deere Service
Page 377:
John Deere Service Keeps You On The
show all

English - StellarSupport - John Deere

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?