AUTO-CUT 300 - Victor Technologies

More documents

Recommendations

Info

6.10 Power Supply Replacement Parts - Right Side Item # Qty Description Ref. Des. Catalog # 1 1 Resistor R7 9-9363 2 1 Rectifier (Diode) D1 9-9345 3 1 Transformer T1 9-9355 for 230/460 VAC units 4 1 Diode D2 9-9486 5 1 Terminal Strip TB3 N/A 2 1 Art # A-04785_AC 3 Manual No. 0-4817 Auto-Cut <strong>300</strong> 6-10 Parts List 4 5
6.11 Power Supply Replacement Parts Item # Qty Description Catalog # 3 Inverter Module 208/230V 9-9360D 3 Inverter Module 400V CE and 400V Non CE 9-9482D 3 Inverter Module 600V 9-9485D Art # A-08284 Manual No. 0-4817 Auto-Cut <strong>300</strong> 6-11 Parts List
Page 1 and 2:
Manual Assembly Instructions - Sepa
Page 3 and 4:
Cut out one strip and use as spine
Page 5 and 6:
300 AUTO-CUT ® PLASMA CUTTING SYST
Page 7 and 8:
300 AUTO-CUT ® PLASMA CUTTING SYST
Page 9 and 10:
! WARNINGS Read and understand this
Page 11 and 12:
INSERT TABLE OF CONTENTS TAB HERE.
Page 13 and 14:
Table of Contents SECTION 1: GENERA
Page 15 and 16:
Table of Contents Appendix 1: Contr
Page 17 and 18:
Table of Contents Insert Section 1
Page 19 and 20:
Manual 0-4817 SECTION 1: GENERAL IN
Page 21 and 22:
THAT HAVE HELD HAZARDOUS SUBSTANCES
Page 23 and 24:
1.06 Documents De Reference Consult
Page 25 and 26:
1.08 Statement of Warranty Manual 0
Page 27 and 28:
Manual 0-4817 AUTO-CUT 300 Insert S
Page 29 and 30:
SECTION 2: SPECIFICATIONS 2.01 Gene
Page 31 and 32:
2.07 Power Supply Dimensions 27.5 i
Page 33 and 34:
2.09 Gas Requirements The customer
Page 35 and 36:
B. Torch Leads Lengths C. Torch Par
Page 37:
Insert Sec. 3 tab here. Discard thi
Page 40 and 41:
3.02 System Layout Refer to section
Page 42 and 43:
3.04 Position the Power Supply Do n
Page 44 and 45:
Check / Adjust Input Voltage Config
Page 46 and 47:
Cutting Machine / Gantry Cutting Ta
Page 48 and 49:
3.06 Ground Connections A. Electrom
Page 50 and 51: 3.08 Connect Work Cable 1. Pass the
Page 52 and 53: 3.10 Connect CNC Cable 1. Connect o
Page 54 and 55: CAUTION Printed circuit boards in t
Page 56 and 57: 3.13 Connect Torch Leads to the Gas
Page 58 and 59: 5 Clamp Art # A-04935_AB Inner Shie
Page 60 and 61: 5. Slide the positioning tube down
Page 62 and 63: Cartridge Tool Art # A-04344 Assemb
Page 64 and 65: Complete the Installation 1. Fill t
Page 66 and 67: This Page Intentionally Blank Manua
Page 69 and 70: 4.01 Power Supply Indicators AC Ind
Page 71 and 72: 4.03 Operating Set-up Follow this s
Page 73 and 74: 4.04 Cut Quality Cut quality requir
Page 75 and 76: 4.05 System Operation This section
Page 77 and 78: 4.06 Operational Suggestions 1. Wai
Page 79 and 80: Fault Code Key Error Code Error Rem
Page 81 and 82: Insert sec 5 tab here. discard this
Page 83 and 84: 5.01 General Maintenance SECTION 5:
Page 85 and 86: 5.04 Coolant Replacement Procedure
Page 87 and 88: 5.06 Arc Starter Spark Gap Adjustme
Page 89: Insert Sec 6 tab here. discard this
Page 92 and 93: 6.02 Leads and Cables Refer to sect
Page 94 and 95: 6.04 Power Supply External Replacem
Page 96 and 97: 6.06 Power Supply Replacement Parts
Page 108 and 109: 6.18 Arc Starter & Gas Control Modu
Page 110 and 111: Manual No. 0-4817 Auto-Cut 300 6-20
Page 112 and 113: Blank
Page 114 and 115: 7.02 O-Ring Lubrication Lubricate a
Page 116 and 117: Electrode Plasma Gas Distributor Ti
Page 118 and 119: 7.05 Coolant Leak Trouble-Shooting
Page 121 and 122: Appendix 1: Control Cable Pinouts P
Page 123 and 124: Manual 0-4817 Auto-Cut 300 A-3 APPE
Page 125 and 126: This page is blank intentionally. M
Page 127 and 128: CNC functions CNC I/O circuits prov
Page 129 and 130: Simplified CNC Circuit J15 CNC 14 p
Page 131 and 132: Installation Art # A-04747 10.5" /
Page 133 and 134: Coolant Return (Red) Art # A-09628
Page 135 and 136: C. Output Connections 1. Refer to t
Page 137 and 138: 1 Nut and 1 Washer Remain in Place
Page 139 and 140: 5. Attach the gas leads from the po
Page 141 and 142: I. Connect Torch Connect the Torch
Page 143 and 144: This page is blank intentionally. M
Page 145 and 146: BASIC GAS CONTROL & ARC STARTER 3 S
Page 147 and 148: 6 6 PILOT REGULATOR (CHOPPER) 1 CN3
Page 149 and 150: 6 CN10 26 CKT RIBBON CABLE TEST SOC
Page 151 and 152:
6 6 PILOT REGULATOR (CHOPPER) 1 CN3
Page 153 and 154:
CN10 26 CKT RIBBON CABLE TEST SOCKE
Page 155 and 156:
16 CKT RIBBON CABLE N (-) P (+) CN6
Page 157 and 158:
6 CN10 26 CKT RIBBON CABLE TEST SOC
Page 159 and 160:
6 6 PILOT REGULATOR (CHOPPER) 1 CN3
Page 161 and 162:
6 CN10 26 CKT RIBBON CABLE TEST SOC
Page 163 and 164:
This Page Intentionally Blank
show all

AUTO-CUT 300 - Victor Technologies

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?