- Page 1 and 2: Manual Assembly Instructions - Sepa
- Page 3 and 4: Cut out one strip and use as spine
- Page 5 and 6: 300 AUTO-CUT ® PLASMA CUTTING SYST
- Page 7 and 8: 300 AUTO-CUT ® PLASMA CUTTING SYST
- Page 9 and 10: ! WARNINGS Read and understand this
- Page 11 and 12: INSERT TABLE OF CONTENTS TAB HERE.
- Page 13 and 14: Table of Contents SECTION 1: GENERA
- Page 15 and 16: Table of Contents Appendix 1: Contr
- Page 17 and 18: Table of Contents Insert Section 1
- Page 19 and 20: Manual 0-4817 SECTION 1: GENERAL IN
- Page 21 and 22: THAT HAVE HELD HAZARDOUS SUBSTANCES
- Page 23 and 24: 1.06 Documents De Reference Consult
- Page 25 and 26: 1.08 Statement of Warranty Manual 0
- Page 27 and 28: Manual 0-4817 AUTO-CUT 300 Insert S
- Page 29 and 30: SECTION 2: SPECIFICATIONS 2.01 Gene
- Page 31 and 32: 2.07 Power Supply Dimensions 27.5 i
- Page 33: 2.09 Gas Requirements The customer
- Page 37: Insert Sec. 3 tab here. Discard thi
- Page 40 and 41: 3.02 System Layout Refer to section
- Page 42 and 43: 3.04 Position the Power Supply Do n
- Page 44 and 45: Check / Adjust Input Voltage Config
- Page 46 and 47: Cutting Machine / Gantry Cutting Ta
- Page 48 and 49: 3.06 Ground Connections A. Electrom
- Page 50 and 51: 3.08 Connect Work Cable 1. Pass the
- Page 52 and 53: 3.10 Connect CNC Cable 1. Connect o
- Page 54 and 55: CAUTION Printed circuit boards in t
- Page 56 and 57: 3.13 Connect Torch Leads to the Gas
- Page 58 and 59: 5 Clamp Art # A-04935_AB Inner Shie
- Page 60 and 61: 5. Slide the positioning tube down
- Page 62 and 63: Cartridge Tool Art # A-04344 Assemb
- Page 64 and 65: Complete the Installation 1. Fill t
- Page 66 and 67: This Page Intentionally Blank Manua
- Page 69 and 70: 4.01 Power Supply Indicators AC Ind
- Page 71 and 72: 4.03 Operating Set-up Follow this s
- Page 73 and 74: 4.04 Cut Quality Cut quality requir
- Page 75 and 76: 4.05 System Operation This section
- Page 77 and 78: 4.06 Operational Suggestions 1. Wai
- Page 79 and 80: Fault Code Key Error Code Error Rem
- Page 81 and 82: Insert sec 5 tab here. discard this
- Page 83 and 84: 5.01 General Maintenance SECTION 5:
- Page 85 and 86:
5.04 Coolant Replacement Procedure
- Page 87 and 88:
5.06 Arc Starter Spark Gap Adjustme
- Page 89:
Insert Sec 6 tab here. discard this
- Page 92 and 93:
6.02 Leads and Cables Refer to sect
- Page 94 and 95:
6.04 Power Supply External Replacem
- Page 96 and 97:
6.06 Power Supply Replacement Parts
- Page 98 and 99:
6.08 Power Supply Replacement Parts
- Page 100 and 101:
6.10 Power Supply Replacement Parts
- Page 102 and 103:
6.12 Power Supply Replacement Parts
- Page 104 and 105:
6.14 Power Supply Replacement Parts
- Page 106 and 107:
6.16 Power Supply Replacement Parts
- Page 108 and 109:
6.18 Arc Starter & Gas Control Modu
- Page 110 and 111:
Manual No. 0-4817 Auto-Cut 300 6-20
- Page 112 and 113:
Blank
- Page 114 and 115:
7.02 O-Ring Lubrication Lubricate a
- Page 116 and 117:
Electrode Plasma Gas Distributor Ti
- Page 118 and 119:
7.05 Coolant Leak Trouble-Shooting
- Page 121 and 122:
Appendix 1: Control Cable Pinouts P
- Page 123 and 124:
Manual 0-4817 Auto-Cut 300 A-3 APPE
- Page 125 and 126:
This page is blank intentionally. M
- Page 127 and 128:
CNC functions CNC I/O circuits prov
- Page 129 and 130:
Simplified CNC Circuit J15 CNC 14 p
- Page 131 and 132:
Installation Art # A-04747 10.5" /
- Page 133 and 134:
Coolant Return (Red) Art # A-09628
- Page 135 and 136:
C. Output Connections 1. Refer to t
- Page 137 and 138:
1 Nut and 1 Washer Remain in Place
- Page 139 and 140:
5. Attach the gas leads from the po
- Page 141 and 142:
I. Connect Torch Connect the Torch
- Page 143 and 144:
This page is blank intentionally. M
- Page 145 and 146:
BASIC GAS CONTROL & ARC STARTER 3 S
- Page 147 and 148:
6 6 PILOT REGULATOR (CHOPPER) 1 CN3
- Page 149 and 150:
6 CN10 26 CKT RIBBON CABLE TEST SOC
- Page 151 and 152:
6 6 PILOT REGULATOR (CHOPPER) 1 CN3
- Page 153 and 154:
CN10 26 CKT RIBBON CABLE TEST SOCKE
- Page 155 and 156:
16 CKT RIBBON CABLE N (-) P (+) CN6
- Page 157 and 158:
6 CN10 26 CKT RIBBON CABLE TEST SOC
- Page 159 and 160:
6 6 PILOT REGULATOR (CHOPPER) 1 CN3
- Page 161 and 162:
6 CN10 26 CKT RIBBON CABLE TEST SOC
- Page 163 and 164:
This Page Intentionally Blank