AUTO-CUT 300 - Victor Technologies

More documents

Recommendations

Info

2.06 Power Supply Specifications & Electrical Requirements Max OCV (U0) Auto-Cut 300 Power Supply Specifications 380 vdc Max Output Current 300 Amps Output Voltage 160 vdc Duty Cycle Rating 100% @ 300A @ 180V (54kW) Operating range 14°F to 122°F (-10°C to + 50°C) Power Factor 0.70 @ 100 ADC Output Cooling Forced Air (Class F) Input Power Input Current Voltage Freq. 3-Ph 3-Ph Fuse (Amps) Wire (AWG) (Volts) (Hz) (kVA) (Amps) 3-Ph 3-Ph 208 50/60 74 206 260 #3/0 2 Auto-Cut 300 Power Supply Input Power Specifications Suggested Sizes (See Note) 230 50/60 72 181 230 #2 2 400 50/60 75 109 135 #3 1 400 (CE) 50/60 89 112 150 #2 1 460 50/60 89 112 150 #2 1 Line Voltages with Suggested Circuit Protection and Wire Sizes Based on National Electric Code and Canadian Electrical Code 1 Extra Hard Usage Type SO, SOW, SOO, SOOW, ST, STW, STO, STOW, STOO, STOOW 2 Extra Hard Usage Type G, G-GC, W CAUTION Fuse and wire sizes are for reference only. The installation must conform to national and local codes for the type and method of wire being used. Manual No. 0-4817 Auto-Cut 300 2-2 SPECIFICATIONS
2.07 Power Supply Dimensions 27.5 inch 700 mm 27 inch 680 mm 33 inch 840 mm 37.75 inch 960 mm Art # A-06886 52.25 inch 1030 mm 60 inch 1050 mm 605 lb / 274 kg Manual No. 0-4817 Auto-Cut 300 2-3 SPECIFICATIONS
Page 1 and 2: Manual Assembly Instructions - Sepa
Page 3 and 4: Cut out one strip and use as spine
Page 5 and 6: 300 AUTO-CUT ® PLASMA CUTTING SYST
Page 7 and 8: 300 AUTO-CUT ® PLASMA CUTTING SYST
Page 9 and 10: ! WARNINGS Read and understand this
Page 11 and 12: INSERT TABLE OF CONTENTS TAB HERE.
Page 13 and 14: Table of Contents SECTION 1: GENERA
Page 15 and 16: Table of Contents Appendix 1: Contr
Page 17 and 18: Table of Contents Insert Section 1
Page 19 and 20: Manual 0-4817 SECTION 1: GENERAL IN
Page 21 and 22: THAT HAVE HELD HAZARDOUS SUBSTANCES
Page 23 and 24: 1.06 Documents De Reference Consult
Page 25 and 26: 1.08 Statement of Warranty Manual 0
Page 27 and 28: Manual 0-4817 AUTO-CUT 300 Insert S
Page 29: SECTION 2: SPECIFICATIONS 2.01 Gene
Page 33 and 34: 2.09 Gas Requirements The customer
Page 35 and 36: B. Torch Leads Lengths C. Torch Par
Page 37: Insert Sec. 3 tab here. Discard thi
Page 40 and 41: 3.02 System Layout Refer to section
Page 42 and 43: 3.04 Position the Power Supply Do n
Page 44 and 45: Check / Adjust Input Voltage Config
Page 46 and 47: Cutting Machine / Gantry Cutting Ta
Page 48 and 49: 3.06 Ground Connections A. Electrom
Page 50 and 51: 3.08 Connect Work Cable 1. Pass the
Page 52 and 53: 3.10 Connect CNC Cable 1. Connect o
Page 54 and 55: CAUTION Printed circuit boards in t
Page 56 and 57: 3.13 Connect Torch Leads to the Gas
Page 58 and 59: 5 Clamp Art # A-04935_AB Inner Shie
Page 60 and 61: 5. Slide the positioning tube down
Page 62 and 63: Cartridge Tool Art # A-04344 Assemb
Page 64 and 65: Complete the Installation 1. Fill t
Page 66 and 67: This Page Intentionally Blank Manua
Page 69 and 70: 4.01 Power Supply Indicators AC Ind
Page 71 and 72: 4.03 Operating Set-up Follow this s
Page 73 and 74: 4.04 Cut Quality Cut quality requir
Page 75 and 76: 4.05 System Operation This section
Page 77 and 78: 4.06 Operational Suggestions 1. Wai
Page 79 and 80: Fault Code Key Error Code Error Rem
Page 81 and 82:
Insert sec 5 tab here. discard this
Page 83 and 84:
5.01 General Maintenance SECTION 5:
Page 85 and 86:
5.04 Coolant Replacement Procedure
Page 87 and 88:
5.06 Arc Starter Spark Gap Adjustme
Page 89:
Insert Sec 6 tab here. discard this
Page 92 and 93:
6.02 Leads and Cables Refer to sect
Page 94 and 95:
6.04 Power Supply External Replacem
Page 96 and 97:
6.06 Power Supply Replacement Parts
Page 98 and 99:
Page 100 and 101:
Page 102 and 103:
Page 104 and 105:
Page 106 and 107:
Page 108 and 109:
6.18 Arc Starter & Gas Control Modu
Page 110 and 111:
Manual No. 0-4817 Auto-Cut 300 6-20
Page 112 and 113:
Blank
Page 114 and 115:
7.02 O-Ring Lubrication Lubricate a
Page 116 and 117:
Electrode Plasma Gas Distributor Ti
Page 118 and 119:
7.05 Coolant Leak Trouble-Shooting
Page 121 and 122:
Appendix 1: Control Cable Pinouts P
Page 123 and 124:
Manual 0-4817 Auto-Cut 300 A-3 APPE
Page 125 and 126:
This page is blank intentionally. M
Page 127 and 128:
CNC functions CNC I/O circuits prov
Page 129 and 130:
Simplified CNC Circuit J15 CNC 14 p
Page 131 and 132:
Installation Art # A-04747 10.5" /
Page 133 and 134:
Coolant Return (Red) Art # A-09628
Page 135 and 136:
C. Output Connections 1. Refer to t
Page 137 and 138:
1 Nut and 1 Washer Remain in Place
Page 139 and 140:
5. Attach the gas leads from the po
Page 141 and 142:
I. Connect Torch Connect the Torch
Page 143 and 144:
This page is blank intentionally. M
Page 145 and 146:
BASIC GAS CONTROL & ARC STARTER 3 S
Page 147 and 148:
6 6 PILOT REGULATOR (CHOPPER) 1 CN3
Page 149 and 150:
6 CN10 26 CKT RIBBON CABLE TEST SOC
Page 151 and 152:
Page 153 and 154:
CN10 26 CKT RIBBON CABLE TEST SOCKE
Page 155 and 156:
16 CKT RIBBON CABLE N (-) P (+) CN6
Page 157 and 158:
Page 159 and 160:
Page 161 and 162:
Page 163 and 164:
This Page Intentionally Blank
show all

AUTO-CUT 300 - Victor Technologies

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?