AUTO-CUT 300 - Victor Technologies

More documents

Recommendations

Info

When finished it should look like photo below. Reinstall the Arc Starter Cover. Ensure that the ground wire is not crimped between the cover and the base assembly. Lower screws (2 per side) Art # A-09625 Upper screws (2 per side) Cover The Arc Starter must be grounded; the grounding terminal is marked . Ground Wire Manual 0-4817 Auto-Cut <strong>300</strong> A-16 APPENDIX
1 Nut and 1 Washer Remain in Place Art # A-04758 Torch Leads Ground Cable Use a clamp to secure the Torch Lead Shield braid to the port on the Remote Arc Starter as shown. Art # A-04759 Torch Leads Shield Shield Clamp Coolant and Pilot Leads to Torch Valve Assembly Manual 0-4817 Auto-Cut <strong>300</strong> A-17 APPENDIX
Page 1 and 2:
Manual Assembly Instructions - Sepa
Page 3 and 4:
Cut out one strip and use as spine
Page 5 and 6:
300 AUTO-CUT ® PLASMA CUTTING SYST
Page 7 and 8:
300 AUTO-CUT ® PLASMA CUTTING SYST
Page 9 and 10:
! WARNINGS Read and understand this
Page 11 and 12:
INSERT TABLE OF CONTENTS TAB HERE.
Page 13 and 14:
Table of Contents SECTION 1: GENERA
Page 15 and 16:
Table of Contents Appendix 1: Contr
Page 17 and 18:
Table of Contents Insert Section 1
Page 19 and 20:
Manual 0-4817 SECTION 1: GENERAL IN
Page 21 and 22:
THAT HAVE HELD HAZARDOUS SUBSTANCES
Page 23 and 24:
1.06 Documents De Reference Consult
Page 25 and 26:
1.08 Statement of Warranty Manual 0
Page 27 and 28:
Manual 0-4817 AUTO-CUT 300 Insert S
Page 29 and 30:
SECTION 2: SPECIFICATIONS 2.01 Gene
Page 31 and 32:
2.07 Power Supply Dimensions 27.5 i
Page 33 and 34:
2.09 Gas Requirements The customer
Page 35 and 36:
B. Torch Leads Lengths C. Torch Par
Page 37:
Insert Sec. 3 tab here. Discard thi
Page 40 and 41:
3.02 System Layout Refer to section
Page 42 and 43:
3.04 Position the Power Supply Do n
Page 44 and 45:
Check / Adjust Input Voltage Config
Page 46 and 47:
Cutting Machine / Gantry Cutting Ta
Page 48 and 49:
3.06 Ground Connections A. Electrom
Page 50 and 51:
3.08 Connect Work Cable 1. Pass the
Page 52 and 53:
3.10 Connect CNC Cable 1. Connect o
Page 54 and 55:
CAUTION Printed circuit boards in t
Page 56 and 57:
3.13 Connect Torch Leads to the Gas
Page 58 and 59:
5 Clamp Art # A-04935_AB Inner Shie
Page 60 and 61:
5. Slide the positioning tube down
Page 62 and 63:
Cartridge Tool Art # A-04344 Assemb
Page 64 and 65:
Complete the Installation 1. Fill t
Page 66 and 67:
This Page Intentionally Blank Manua
Page 69 and 70:
4.01 Power Supply Indicators AC Ind
Page 71 and 72:
4.03 Operating Set-up Follow this s
Page 73 and 74:
4.04 Cut Quality Cut quality requir
Page 75 and 76:
4.05 System Operation This section
Page 77 and 78:
4.06 Operational Suggestions 1. Wai
Page 79 and 80:
Fault Code Key Error Code Error Rem
Page 81 and 82:
Insert sec 5 tab here. discard this
Page 83 and 84:
5.01 General Maintenance SECTION 5:
Page 85 and 86: 5.04 Coolant Replacement Procedure
Page 87 and 88: 5.06 Arc Starter Spark Gap Adjustme
Page 89: Insert Sec 6 tab here. discard this
Page 92 and 93: 6.02 Leads and Cables Refer to sect
Page 94 and 95: 6.04 Power Supply External Replacem
Page 96 and 97: 6.06 Power Supply Replacement Parts
Page 108 and 109: 6.18 Arc Starter & Gas Control Modu
Page 110 and 111: Manual No. 0-4817 Auto-Cut 300 6-20
Page 112 and 113: Blank
Page 114 and 115: 7.02 O-Ring Lubrication Lubricate a
Page 116 and 117: Electrode Plasma Gas Distributor Ti
Page 118 and 119: 7.05 Coolant Leak Trouble-Shooting
Page 121 and 122: Appendix 1: Control Cable Pinouts P
Page 123 and 124: Manual 0-4817 Auto-Cut 300 A-3 APPE
Page 125 and 126: This page is blank intentionally. M
Page 127 and 128: CNC functions CNC I/O circuits prov
Page 129 and 130: Simplified CNC Circuit J15 CNC 14 p
Page 131 and 132: Installation Art # A-04747 10.5" /
Page 133 and 134: Coolant Return (Red) Art # A-09628
Page 135: C. Output Connections 1. Refer to t
Page 139 and 140: 5. Attach the gas leads from the po
Page 141 and 142: I. Connect Torch Connect the Torch
Page 143 and 144: This page is blank intentionally. M
Page 145 and 146: BASIC GAS CONTROL & ARC STARTER 3 S
Page 147 and 148: 6 6 PILOT REGULATOR (CHOPPER) 1 CN3
Page 149 and 150: 6 CN10 26 CKT RIBBON CABLE TEST SOC
Page 153 and 154: CN10 26 CKT RIBBON CABLE TEST SOCKE
Page 155 and 156: 16 CKT RIBBON CABLE N (-) P (+) CN6
Page 163 and 164: This Page Intentionally Blank
show all

AUTO-CUT 300 - Victor Technologies

Create successful ePaper yourself

Delete template?

Save as template?