Laboratory Manual - King Fahd University of Petroleum and Minerals

More documents

Recommendations

Info

Diode Models The diode element model is given in Figure 1. The element statement format is given by Dname NA NC MNAME [AREA] NA MNAME NC I D The associated model statement is Figure 1: Junction Diode. .MODEL MNAME D [PNAME1=PVAL1 PNAME2=PVAL2…] The anode of the diode is connected to NA; the cathode to NC. MNAME is an alphanumeric model designation for the device. Detailed model parameters are provided in Table 1. Bipolar Junction Transistor The npn and pnp transistor element models are shown in Figure 2. The element statement format is Qname NC NB NE MNAME [AREA] NC NC NB NB NE NPN Figure 2: BJT types. NE PNP The associated model statements is or .MODEL MNAME npn [PNAME1=PVAL1 PNAME2=PVAL2…] .MODEL MNAME pnp[PNAME1=PVAL1 PNAME2=PVAL2…] 4
Detailed model parameters are provided in Table 2. MOS Field Effect Transistor The n-channel and p-channel MOSFET element models are given in Figure 3. The element statement format is Mname ND NG NS NB MNAME W=VALW L=VALL ND ND NG NB NG NB NS NS 5 NMOS PMOS Figure 3: MOSFET types. The associated model statements is for N-channel .MODEL MNAME NMOS [PNAME1=PVAL1 PNAME2=PVAL2…] and for P-channel .MODEL MNAME PMOS[PNAME1=PVAL1 PNAME2=PVAL2…] Detailed model parameters are provided in Table 3. Note that the default values for the gate length, VALL, and the gate width, VALW, are 1cm. Obviously, these are not realistic values; however, the model uses the ratio of VALL and VALW rather than the individual values in its calculations. CONTROL COMMANDS .OP The inclusion of the statement .OP makes SPICE perform DC analysis to find the operating point of the circuit. .AC Sweep-mode NP START STOP The .AC control statement is used to perform ac analysis on a circuit and provide data for frequency response plotting. Where Sweep-mode is one of the keywords that’s indicates the frequency variation by decade (DEC), by octave (OCT), or linearly (LIN). NP is the number of points per sweep-mode; FSTART is the starting frequency. FSTART cannot be zero.
Page 1 and 2: King Fahd University of Petroleum a
Page 3: 4. You can use upper or lower case
Page 7 and 8: ‣ Run the program Once you are in
Page 9 and 10: |Av(jω)| [dB] A m F L (jω) F H (j
Page 11 and 12: Spice Transistor Model .model Q2N39
Page 13 and 14: TABLE 2: DETAILED BJT MODEL PARAMET
Page 15 and 16: KING FAHD UNIVERSITY OF PETROLEUM A
Page 17 and 18: SPICE Simulation: SPICE simulations
Page 19 and 20: Table I: Measurement results With C
Page 21 and 22: This page to be submitted with the
Page 23 and 24: where R R 1 // R 2 // r and ' in B
Page 25 and 26: 4. Use three parastic capacitances
Page 29 and 30: 1 The output voltage in time domain
Page 31 and 32: 10k Differentiator 1500pF 2 3 7 - 7
Page 33 and 34: A SUBCIRCUIT may be called as follo
Page 35 and 36: 35 6. Construct the differentiator
Page 37 and 38: MINI-SYSTEM Now, you should be appl
Page 39 and 40: vo ( s) R2 / R1 v ( ) s i s 1 R w
Page 41 and 42: DL1 4 5 DIODE DL2 6 4 DIODE VL1 5 0
Page 43 and 44: DEMONSTRATION: NETWORK ANALYZER The
Page 45 and 46: R 1 2 3 7 - 741 + +15V 4 -15V 6 V o
Page 47 and 48: considering the op amp connected as
Page 49 and 50: frequency at, say 1kHz, then the ou
Page 53 and 54: General (bilinear) filter a s a Ts
Page 55 and 56:
This page to be submitted with the
Page 57 and 58:
Page 59 and 60:
The filter parameters are as follow
Page 61 and 62:
SPICE simulation: 3. Use SPICE simu
Page 63 and 64:
Page 65 and 66:
+V DD =5V 100k R 2 R D 4.3k C 2 R s
Page 67 and 68:
You must have your SPICE output fil
Page 69 and 70:
Page 71 and 72:
Amplitude Controll Althogh the freq
Page 73 and 74:
73 COMPONENTS 1. Digital Oscillosco
Page 75 and 76:
Page 77 and 78:
V i 2 3 +15V 7 - 741 + 6 4 -15V R 1
Page 79 and 80:
4. Capacitors: C=0.1μF (2 NOs), 15
Page 81 and 82:
APPENDIX 1. Capacitors and Resistor
Page 83:
83 2. Data sheet for MOSFET # 2N435
Page 87:
87 4. Data sheet for op amp 741.
show all

Laboratory Manual - King Fahd University of Petroleum and Minerals

Create successful ePaper yourself

Delete template?

Save as template?