Operator and Installation Manual Tron AIS TR-8000.pdf - Jotron

More documents

Recommendations

Info

8.3.1.6 Pilot / Aux. Display connection This Port may be mandatory to be used with Pilot port connector (See picture below) on some kind of vessels. Otherwise, this port may be used to connect a secondary display (Maybe ARPA radar, if “External display” is connected to ECS/ECDIS) This port is one of two options to connect a Pilot connector, as it is also possible to connect Pilot port cable to the TR-8000 Display Unit, see chapters 8.3.2 and 10.2.1.3 Figure 8-14 Pilot plug with cable Default speed on this port is 38400 baud. # In/Out Type Usage Name Connects to AMP 206486-1 Pin no: 16 In RD4-B(+) 6 17 IEC61162-2 Pilot / Aux RD4-GND (Iso Gnd) 9 18 In (RS422) Display RD4-A(-) 5 19 Out TD4-A(-) 1 20 TD4-GND (Iso Gnd) 21 Out TD4-B(+) 4 Figure 8-15 AMP 206486-1 (Pilot Plug) pinout TR-8000 Operator and Installation Manual 56
8.3.1.7 Alarm Connection Below picture shows where to connect external alarm to TR-8000 # In/Out Type Usage Name 37 Out Relay (NC) Alarm ALARM_A 38 Out ALARM_B Figure 8-16 Typical Alarm connection In this configuration, both the external relay and the alarm unit are powered from external power source, and the alarm unit is grounded through the external relay if an alarm occurs or the main power to the AIS is removed or defective. Other configurations may be used, but remember that the Alarm must function both on AIS Alarm conditions, and power failure to the AIS. The Alarm relay is a normally closed earth free relay contact, provided as an independent and simple method for triggering an external alarm. The alarm relay is active in case of power off and is capable of driving a 2A current. The maximum voltage over the alarm relay must not exceed 48V. The alarm relay is deactivated upon acknowledgment of an alarm, either internally on the display unit, or by an externally provided ACK sentence. If the Transponder power is lost, and the Alarm relay has power, the alarm will be triggered. In this case, the only way to deactivate the Alarm is to power the Transponder unit or disconnect the power source of the Alarm relay. TR-8000 Operator and Installation Manual 57
Page 2 and 3:
Table of Contents 1 Revision Histor
Page 4 and 5:
8.3.1.2 Label in transponder with c
Page 6 and 7: 1 Revision History Revision no. By
Page 8 and 9: 3 Introduction 3.1 Safety Instructi
Page 10 and 11: 4 Operation general introduction Th
Page 12 and 13: 6 TR-8000 Description The Tron AIS
Page 14 and 15: 6.2 Transponder Unit The Transponde
Page 16 and 17: 6.2.5 External Display (Ethernet) C
Page 18 and 19: 7 Operational description The opera
Page 20 and 21: 7.2 Display Unit menu system. Statu
Page 22 and 23: 7.2.4 Important Buttons shown in di
Page 24 and 25: 7.2.6 Ship List The display unit re
Page 26 and 27: 7.2.7 Graphical View The graphical
Page 28 and 29: 7.3 Voyage Settings Red square show
Page 30 and 31: 7.3.2 Destination The destination o
Page 32 and 33: 7.3.6 Draught The Draught parameter
Page 34 and 35: 7.4.2 Popup when received message E
Page 36 and 37: 7.4.4.1 Message recipients “From
Page 38 and 39: 7.5 Display Settings Red square sho
Page 40 and 41: 8.1.2 Display Unit The display unit
Page 42 and 43: 8.1.2.3 Flush/ Panel Mounting Figur
Page 44 and 45: 8.1.3.1 GPS Antenna When selecting
Page 46 and 47: 8.1.3.2 VHF Antenna When individual
Page 48 and 49: 8.2.2 VHF antenna The table below s
Page 50 and 51: 8.3.1 Transponder In order to conne
Page 52 and 53: 8.3.1.2 Label in transponder with c
Page 54 and 55: 8.3.1.4 Sensor connections Sensors
Page 58 and 59: 8.3.1.8 Detailed description of con
Page 60 and 61: 8.3.2 Display Unit: The TR-8000 Dis
Page 62 and 63: Transponder (RJ45): Figure 8-20 Eth
Page 64 and 65: - Not subject to target loss due to
Page 66 and 67: 10.1.1.1 Type of Vessel Select Type
Page 68 and 69: 10.1.2 Display Settings Red square
Page 70 and 71: 10.1.3.2 View Regions It is possibl
Page 72 and 73: 10.1.3.3.1 Change Channel NOTE! BE
Page 74 and 75: 10.1.3.3.3 Output Power The button
Page 76 and 77: 10.1.3.3.5.1 Illegal Coordinates Ex
Page 78 and 79: The internal Alarm is triggered if
Page 80 and 81: 032 Heading lost/invalid External h
Page 82 and 83: 10.1.4 Indicators Red square shows
Page 84 and 85: 10.2.1.1 Display/ Transponder IP NO
Page 86 and 87: 10.2.1.3 Aux. Display/Pilot Port Re
Page 88 and 89: 10.2.1.5 Priorities From this menu
Page 90 and 91: 10.2.2 VHF link/Long Range Red squa
Page 92 and 93: 10.2.2.5 Test Communication The Com
Page 94 and 95: 10.2.4 Internal GPS Red square show
Page 96 and 97: 10.2.6 Self Test Red square shows b
Page 98 and 99: 10.2.8 Current position Red square
Page 100 and 101: 12 List of VHF Channels Channel Fre
Page 102 and 103: 14 Outline Drawings 14.1 TR-8000 Tr
Page 104 and 105: 14.3 TR-8000 Display Unit, Flush/Pa
Page 106 and 107:
14.5 Procom CXL 2-1LW/h Maritime VH
Page 108 and 109:
14.7 SANAV - GPS Marine Antenna Fig
Page 110 and 111:
15 Abbreviations and Definitions AC
Page 112 and 113:
RCC RF RMS ROT RNG RX SAR S/N SOG S
Page 114 and 115:
16 Service Procedure WARRANTY CLAIM
Page 116 and 117:
16.2 Trouble Description Form For b
Page 118 and 119:
18 List of Figures Figure 7-1 Trans
show all

Operator and Installation Manual Tron AIS TR-8000.pdf - Jotron

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?