User Manual - JVL Industri Elektronik A/S

More documents

Recommendations

Info

1.4 Getting Started — Gear Mode (Mode 1) AMC11B/12B does not use terminals P- and P+ since it includes a mains supply. See Power Supply section! Industry busin User Outputs User Inputs IA1 IA2 IA3 IA4 O+ O8 O7 O6 O5 O4 O3 O2 O1 O- IN8 IN7 IN6 IN5 IN4 IN3 IN2 IN1 IN- 1C 2C 3C 4C 5C 6C 7C 8C 9C 10C 11C 12C 13C 14C 15C 16C 17C 18C 19C 20C 21C 22C 23C 24C 25C 26C 27C 28C 29C 30C 31C 32C 1A P- 2A P+ 3A FA 4A FB 5A FC 6A FD 7A PDO 8A IB1 9A IB2 10A IB3 11A IB4 12A HLA 13A HLB 14A HLC 15A 5VO 16A EZ1 17A EZ2 18A EA1 19A EA2 20A EB1 21A EB2 22A ECM 23A XCM 24A XI 25A YCM 26A YI 27A O5V 28A AO 29A BO 30A OCM 31A AIN 32A ACM 26B NL 27B PL 28B HM 30B AX2 31B TCM 32B TAC Power Supply in 15-80V DC Power Dump output Industry bus out HallInput Screen 23A-26APulseInputs Pulse Outputs +/-10V Input Screen End-of-travel inputs Home(Reset) input Secondaryaxis Analogueoutput (torque monitor) + Screen Note !:screenonly connectedtosignal source. For electronic gearing an incremental encoder is used Channel A Ground Channel B PLC or Pulse Generator Pulse output Ground Direction output PNP outputs TT0017GB Follow the procedure below for operation of the Controller in Mode 1 (Gear Mode) 1. Connect the Controller as shown above. For further details, see: Motor Connection, page 21 / Encoder Input, page 28 / Power Supply, page 31 / Pulse Inputs, page 33. 2. Connect the PC via a terminal program (e.g. JVL’s MotoWare or Windows Terminal), if necessary following the description of the RS232 interface in RS232 Interface, page 38. 3. Switch on the Controller, but ensure that all inputs are inactive. Only the Power LED and possibly Out 1 may be active. If one or more of the red LEDs is active or blinks, the Controller is most likely set up for the wrong motor type. Follow the instructions in General Aspects of Installation, page 12 4. Send the command ? (enter) to the Controller and wait until the Controller responds with a status overview. If the status overview is displayed, the RS232 interface and power supply are connected correctly. 5. Set the Controller to Gear Mode by sending the command MO=1 (enter). The Controller should respond Y, indicating that Gear Mode (Mode 1) has been selected. 6. By default, the servo parameters KD, KP, and KI are set to typical, moderate values. This means that the motor can be operated without further adjustment. For optimum system operation however, the parameters should be adjusted. See Adjustment of Servo Regulation, page 16. 7. The Controller is now set to Gear Mode. JVL Industri Elektronik A/S - User Manual - AC servocontroller AMC10/11/12 5
1.5 Getting Started — Positioning Mode (Mode 2) AMC11B/12B does not use terminals P- and P+ since it includes a mains supply. See Power Supply section! Industrybus in User Outputs User Inputs IA1 IA2 IA3 IA4 O+ O8 O7 O6 O5 O4 O3 O2 O1 O- IN8 IN7 IN6 IN5 IN4 IN3 IN2 IN1 IN- 1C 2C 3C 4C 5C 6C 7C 8C 9C 10C 11C 12C 13C 14C 15C 16C 17C 18C 19C 20C 21C 22C 23C 24C 25C 26C 27C 28C 29C 30C 31C 32C 1A P- 2A P+ 3A FA 4A FB 5A FC 6A FD 7A PDO 8A IB1 9A IB2 10A IB3 11A IB4 12A HLA 13A HLB 14A HLC 15A 5VO 16A EZ1 17A EZ2 18A EA1 19A EA2 20A EB1 21A EB2 22A ECM 23A XCM 24A XI 25A YCM 26A YI 27A O5V 28A AO 29A BO 30A OCM 31A AIN 32A ACM 26B NL 27B PL 28B HM 30B AX2 31B TCM 32B TAC Power Supplyin 15-80V DC Power Dumpoutput Industry bus out Hall Input Screen PulseInputs Pulse Outputs +/- 10V Input Screen End-of-travel inputs Home (Reset) Input Secondary axis Analogueoutput (torquemonitor) + TT0018GB Follow the procedure below for operation of the Controller in Mode 2 (Positioning Mode) 1. Connect the Controller as shown above. For further details, see: Motor Connection, page 21 / Encoder Input, page 28 / Power Supply, page 31. 2. Connect the PC via a terminal program (e.g. JVL’s MotoWare or Windows Terminal), if necessary following the description of the RS232 interface in RS232 Interface, page 38. 3. Switch on the Controller, but ensure that all inputs are inactive. Only the Power LED and possibly Out 1 may be active. If one or more of the red LEDs is active or blinks, the Controller is most likely set up for the wrong motor type. Follow the instructions in General Aspects of Installation, page 12 4. Send the command ? (enter) to the Controller and wait until the Controller responds with a status overview. If the status overview is displayed, the RS232 interface and power supply are connected correctly. 5. Set the Controller to Positioning Mode by sending the command MO=2 (enter). The Controller should respond Y, indicating that Positioning Mode has been selected. 6. By default, the servo parameters KD, KP, and KI are set to typical, moderate values. This means that the motor can be operated without further adjustment. For optimum system operation however, the parameters must be adjusted. See Adjustment of Servo Regulation, page 16. 7. The Controller is now set to Positioning Mode. As a test, the motor can be moved to absolute position 1000 by sending the command SP=1000 (enter). The motor should move to the specified position. By sending the command SP=-1000 (enter), the motor will move in the opposite direction to position -1000. If this does not occur, or if the motor runs for a very long time, it may be due to the fact that the position counter either was at position 1000, or that the previous position was far from 1000. See Positioning Mode (MO=2), page 48 and Command Description, page 67 for details of other commands. 6 JVL Industri Elektronik A/S - User Manual - AC servocontroller AMC10/11/12
Page 1 and 2: AMC10B / AMC10C AMC11B AMC12B / AMC
Page 3 and 4: Contents 1 Introduction ...........
Page 5 and 6: 1.1 Features = Extended functions i
Page 7: 1.3 Overview of Operating Modes 1.3
Page 11 and 12: 1.7 Getting Started — Velocity Mo
Page 13 and 14: 10 JVL Industri Elektronik A/S - Us
Page 15 and 16: 2.1 General Aspects of Installation
Page 17 and 18: 2.2 Transfer of Parameters to the C
Page 19 and 20: 2.3 Adjustment of Servo Regulation
Page 23 and 24: 3.1 Connections (Connector DIN41612
Page 25 and 26: 3.2 Motor Connection Industry bus i
Page 27 and 28: 3.3 User Inputs This diagram is use
Page 29 and 30: 3.5 Home (Reset) Input (Connector D
Page 31 and 32: 3.7 Encoder Input (Connector DIN416
Page 33 and 34: 3.8 Hall Input (Connector DIN41612
Page 35 and 36: 3.9 Power Supply JVL Industri Elekt
Page 37 and 38: 3.10 Pulse Inputs Input Configurati
Page 39 and 40: 3.12 Analogue Input Industry busin
Page 41 and 42: 3.14 RS232 Interface 3.14.1 Interfa
Page 43 and 44: 3.14 RS232 Interface 3.14.7 Connect
Page 45 and 46: 3.16 Module Interface Controller AM
Page 49 and 50: 4.1 Use of RS232 Commands The AMC C
Page 51 and 52: 4.3 Positioning Mode (MO=2) In this
Page 53 and 54: 4.4 Register Mode (MO=3) Table -1 -
Page 55 and 56: 4.5 Velocity Mode (MO=4) Analogue c
Page 57 and 58: 4.7 Program Execution in the AMC12
Page 59 and 60:
4.7 Program Execution in the AMC12
Page 61 and 62:
Page 63 and 64:
Page 65 and 66:
Page 67 and 68:
Page 69 and 70:
4.9 Adjustment of Analogue Input Th
Page 71 and 72:
4.10 Command Description 4.10.3 Acc
Page 73 and 74:
4.10 Command Description 4.10.7 Act
Page 75 and 76:
4.10 Command Description 4.10.11 Av
Page 77 and 78:
4.10 Command Description 4.10.15 Pe
Page 79 and 80:
4.10 Command Description 4.10.21 En
Page 81 and 82:
4.10 Command Description Table -3 -
Page 83 and 84:
4.10 Command Description 4.10.29 Ex
Page 85 and 86:
4.10 Command Description 4.10.33 HA
Page 87 and 88:
4.10 Command Description 4.10.35 In
Page 89 and 90:
4.10 Command Description 4.10.39 In
Page 91 and 92:
4.10 Command Description 4.10.44 Sh
Page 93 and 94:
4.10 Command Description 4.10.49 Fe
Page 95 and 96:
4.10 Command Description 4.10.54 Re
Page 97 and 98:
Page 99 and 100:
4.10 Command Description 4.10.61 Sh
Page 101 and 102:
4.10 Command Description 4.10.67 Ph
Page 103 and 104:
4.10 Command Description 4.10.70 Pr
Page 105 and 106:
4.10 Command Description 4.10.71 En
Page 107 and 108:
Page 109 and 110:
4.10 Command Description 4.10.79 Sy
Page 111 and 112:
4.10 Command Description 4.10.83 Se
Page 113 and 114:
Page 115 and 116:
4.10 Command Description 4.10.93 Ac
Page 117 and 118:
4.10 Command Description 4.10.97 Ze
Page 119 and 120:
4.11 Error Messages E5: It is not a
Page 121 and 122:
4.11 Error Messages E28: Encoder er
Page 123 and 124:
4.12 Alphabetical Overview of Comma
Page 125 and 126:
4.12 Alphabetical Overview of Comma
Page 127 and 128:
5.1 Technical Data Description Min.
Page 129 and 130:
5.2 Physical Dimensions 5.2.2 Physi
Page 131 and 132:
5.3 Servo Loop The Controller uses
Page 133 and 134:
5.5 Common Errors During installati
Page 135 and 136:
5.6 Connection of an unknown motor
Page 137 and 138:
Page 139 and 140:
Page 141 and 142:
Page 143 and 144:
Page 145 and 146:
Page 147 and 148:
5.7 Examples of Motor Connection 5.
Page 149 and 150:
5.9 Connector Board As an accessory
Page 151 and 152:
6 Index Register Mode 7, 47 Torque
show all

User Manual - JVL Industri Elektronik A/S

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?