Samsung ME40C User Manual - Touch Screens Inc.

More documents

Recommendations

Info

Other issue The IR sensor is not functioning. Make sure the sensor light turns on when a button is pressed on the remote control. •• If the sensor light does not turn on, turn the power switch off and then on again on the back of the product. (The power LED lights up red when the screen is switched off.) If the sensor light still does not turn on after the power switch is turned off and then on again, an internal jack may be disconnected. Contact your nearest service centre to have the product serviced. •• If the sensor light that is on does not flash red when a button is pressed on the remote control, the IR sensor may be defective. Contact your nearest service centre to have the product serviced. •• If there is no change on the screen when a button is pressed on the remote control although the sensor light flashes red, the mainboard may be defective. Contact your nearest service centre to have the product serviced. In power-saving mode, when the input source is DisplayPort, PC display settings cannot be saved. When booting the PC with the input source set to DisplayPort, the BIOS and booting screens do not appear. Go to System → General and set Max. Power Saving to Off. Alternatively, configure the PC display output settings again. Ensure the set is turned on. Boot the PC when the set is turned on or when the input source is not DisplayPort. 228
Q & A Refer to the user manual for your PC or graphics card for further instructions on adjustment. Question How can I change the frequency? How can I change the resolution? Answer Set the frequency on your graphics card. •• Windows XP: Go to Control Panel → Appearance and Themes → Display → Settings → Advanced → Monitor and adjust the frequency in Monitor Settings. •• Windows ME/2000: Go to Control Panel → Display → Settings → Advanced → Monitor and adjust the frequency in Monitor Settings. •• Windows Vista: Go to Control Panel → Appearance and Personalization → Personalize → Display Settings → Advanced Settings → Monitor and adjust the frequency in Monitor Settings. •• Windows 7: Go to Control Panel → Appearance and Personalization → Display → Adjust resolution → Advanced Settings → Monitor and adjust the frequency in Monitor Settings. •• Windows 8: Go to Settings → Control Panel → Appearance and Personalization → Display → Adjust resolution → Advanced Settings → Monitor and adjust the frequency in Monitor Settings. •• Windows XP: Go to Control Panel → Appearance and Themes → Display → Settings and adjust the resolution. •• Windows ME/2000: Go to Control Panel → Display → Settings and adjust the resolution. •• Windows Vista: Go to Control Panel → Appearance and Personalization → Personalize → Display Settings and adjust the resolution. •• Windows 7: Go to Control Panel → Appearance and Personalization → Display → Adjust Resolution and adjust the resolution. •• Windows 8: Go to Settings → Control Panel → Appearance and Personalization → Display → Adjust Resolution and adjust the resolution. 229
Page 1 and 2:
LFD DISPLAY User Manual ME32C ME40C
Page 3 and 4:
Table of contents Main Screen Layou
Page 5 and 6:
Table of contents AllShare Play Wha
Page 7 and 8:
Chapter 01 Before Using the Product
Page 9 and 10:
Storage Due to the characteristics
Page 11 and 12:
Do not install the product on an un
Page 13 and 14:
Do not use or keep combustible spra
Page 15 and 16:
Chapter 02 Preparations Checking th
Page 17 and 18:
Checking the Components -- Contact
Page 19 and 20:
Parts ―― The colour and shape o
Page 21 and 22:
POWER Reverse Side ―― The colou
Page 23 and 24:
Remote Control ―― Using other d
Page 25 and 26:
Adjusting the OSD with the Remote C
Page 27 and 28:
Before Installing the Product (Inst
Page 29 and 30:
Installing the Wall Mount Preparing
Page 31 and 32:
Remote Control (RS232C) •• Pin
Page 33 and 34:
•• Connector : RJ45 Direct LAN
Page 35 and 36:
Control Codes Viewing control state
Page 37 and 38:
Input source control 0x24 HDMI2_PC
Page 39 and 40:
PIP On/Off control •• Function
Page 41 and 42:
Video Wall On •• Function Turn
Page 43 and 44:
Wall_SNo: Product Number code assig
Page 45 and 46:
POWER POWER Connecting to a PC •
Page 47 and 48:
POWER Connection Using an DP Cable
Page 49 and 50:
Changing the Resolution on Windows
Page 51 and 52:
POWER POWER Connection Using an HDM
Page 53 and 54:
Connecting the network box (Sold se
Page 55 and 56:
Changing the Input source Source So
Page 57 and 58:
MDC Program Installation/Uninstalla
Page 59 and 60:
POWER Using MDC via Ethernet Enter
Page 61 and 62:
Connection Management Connection ma
Page 63 and 64:
Auto Set ID Auto Set ID feature ass
Page 65 and 66:
Command Retry This feature is used
Page 67 and 68:
Main Screen Layout 1 6 1 Menu Bar C
Page 69 and 70:
User Login User Settings •• Add
Page 71 and 72:
MPEG Noise Filter Reduces MPEG nois
Page 73 and 74:
Advanced Settings Dynamic Contrast
Page 75 and 76:
Format •• Select the format to
Page 77 and 78:
Security Safety Lock •• Lock th
Page 79 and 80:
Holiday Management Holiday Manageme
Page 81 and 82:
Safety Screen The Safety Screen fun
Page 83 and 84:
Tool Settings Security •• Panel
Page 85 and 86:
Monitor Window A window appears sho
Page 87 and 88:
Group Management Creating Groups Cr
Page 89 and 90:
Renaming Groups 1 Select a group na
Page 91 and 92:
Troubleshooting Guide -- This progr
Page 93 and 94:
Chapter 05 Screen Adjustment Config
Page 95 and 96:
Screen Adjustment MENUm → Picture
Page 97 and 98:
Position Screen Adjustment Picture
Page 99 and 100:
Resolution Select Screen Adjustment
Page 101 and 102:
Advanced Settings MENUm → Picture
Page 103 and 104:
Advanced Settings White Balance 10p
Page 105 and 106:
Picture Options MENUm → Picture
Page 107 and 108:
Picture Options HDMI Black Level Fi
Page 109 and 110:
Chapter 06 Sound Adjustment Configu
Page 111 and 112:
Speaker Settings MENUm → Sound
Page 113 and 114:
Chapter 07 Network Network Settings
Page 115 and 116:
3 On the dialog that appears, click
Page 117 and 118:
How to set up manually 1 Go to the
Page 119 and 120:
Soft AP AllShare Settings MENU m
Page 121 and 122:
Time MENUm → System → Time →
Page 123 and 124:
Time On Timer Off Timer Holiday Man
Page 125 and 126:
Rotate menu MENUm → System → Ro
Page 127 and 128:
Security MENUm → System → Secur
Page 129 and 130:
Auto Protection Time MENUm → Syst
Page 131 and 132:
Screen Burn Protection Pixel Shift
Page 133 and 134:
Ticker MENUm → System → Ticker
Page 135 and 136:
Video Wall Video Wall · Format ·
Page 137 and 138:
General MENUm → System → Genera
Page 139 and 140:
General Sound Feedback Auto Power S
Page 141 and 142:
Anynet+ (HDMI-CEC) Anynet+ (HDMI-CE
Page 143 and 144:
Problem The connected device is not
Page 145 and 146:
Magic Clone MENUm → System → Ma
Page 147 and 148:
Chapter 09 Support Software Update
Page 149 and 150:
AllShare Play MENU m → Support
Page 151 and 152:
Compatible devices with AllShare Pl
Page 153 and 154:
Connecting to a PC over a network P
Page 155 and 156:
Using the Basic AllShare Play Featu
Page 157 and 158:
My list MENUm → Support → Conte
Page 159 and 160:
Photos MENUm → Support → Conten
Page 161 and 162:
Videos / Photos / Music Play Option
Page 163 and 164:
Supported Subtitle and AllShare Pla
Page 165 and 166:
File Extension Container Video Code
Page 167 and 168:
Contents File Extension Container V
Page 169 and 170:
Flash •• Compatible with Flash
Page 171 and 172:
Approving a connected device from t
Page 173 and 174:
MagicInfo Lite 2 Select Network sch
Page 175 and 176:
USB Device Auto Play MagicInfo Lite
Page 177 and 178: 4 Select Contents to specify the co
Page 179 and 180: 3 Select Edit. Edit Time 12:00 am~
Page 181 and 182: Viewing the details of a Local sche
Page 183 and 184: Content manager 2 Select the conten
Page 185 and 186: Settings Settings Server Network Se
Page 187 and 188: When Content is Running Viewing the
Page 189 and 190: Chapter 12 MagicInfo Premium S - -
Page 191 and 192: Flash Power Point PDF •• Compat
Page 193 and 194: Network Schedule Multiframe Playbac
Page 195 and 196: Approving a connected device from t
Page 197 and 198: MagicInfo Premium S 2 Select Networ
Page 199 and 200: Internal Auto Play Network schedule
Page 201 and 202: 4 Select Contents to specify the co
Page 203 and 204: 3 Select Edit. Edit Time 12:00 am~
Page 205 and 206: Viewing the details of a Local sche
Page 207 and 208: Template Manager 2 Select Create in
Page 209 and 210: 5 Select sound or background music.
Page 211 and 212: Deleting content 1 Select Content m
Page 213 and 214: Default content duration Specify th
Page 215 and 216: Changing the settings for the conte
Page 217 and 218: Video •• 3D video is not suppor
Page 219 and 220: MagicInfo Videowall S MENUm → Sup
Page 221 and 222: Chapter 14 Troubleshooting Guide Re
Page 223 and 224: Screen issue The screen is not clea
Page 225 and 226: Sound issue There is no sound. Chec
Page 227: Other issue The product smells like
Page 231 and 232: Chapter 15 Specifications 1 Size Ge
Page 233 and 234: ―― Plug-and-Play This monitor c
Page 235 and 236: Preset Timing Modes -- Horizontal F
Page 237 and 238: Chapter 16 Appendix Contact SAMSUNG
Page 239 and 240: LATIN AMERICA PUERTO RICO 1-800-682
Page 241 and 242: EUROPE ROMANIA 08008 SAMSUNG (08008
Page 243 and 244: ASIA PACIFIC PHILIPPINES 1-800-10-S
Page 245 and 246: AFRICA SOUTH AFRICA 0860-SAMSUNG (7
Page 247 and 248: WEEE Correct Disposal of This Produ
Page 249 and 250: Prevention of Afterimage Burn-in Bl
Page 251 and 252: Licence Manufactured under licence
show all

Samsung ME40C User Manual - Touch Screens Inc.

Create successful ePaper yourself

Delete template?

Save as template?