26 Offices Sydney – Melb<strong>our</strong>ne – Brisbane – Perth
www.techrentals.com.au Electrical Power Micro-Ohm Meters & Earth Testers cont’d. Megger DLRO10 Micro-Ohm Meter MEG,DLRO10 (2661) AU Self contained fully automatic micro-ohm meter, selecting the most suitable test current up to 10Adc. Range 0.1μΩ to 2kΩ, resolution 0.1μΩ. LED display. Rechargeable battery. Megger DLRO10X Digital Low Resistance Ohm Meter 10A/0.1μΩ-2KOhm MEG,DLRO10X (2633) AU/MY Self contained fully automatic (with manual option) micro-ohm meter, selecting the most suitable test current up to 10Adc. Range 0.1μΩ to 2kΩ, resolution 0.1μΩ. Internal memory for 700 tests. <strong>Download</strong> software supplied. RS232 communications to PC. LCD display. Rechargeable battery. Megger DLRO200 200A Micro-Ohm Meter MEG,DLRO200 (2664) AU Test current range 10A to 200Adc. Measurement range 0.1mΩ to 1Ω, resolution 0.1mΩ. Current cables 2 x 5m. Internal memory for 300 tests. <strong>Download</strong> software supplied. RS232 communications to PC. LCD display. Megger DLRO600 Digital Micro-Ohm Meter - High current MEG,DLRO600 (2665) AU/MY Test current range 10A to 600Adc. Measurement range 0.1μΩ to 1Ω, resolution 0.1μΩ. Current cables 2x5m. Internal memory for 300 tests. <strong>Download</strong> software. Megger DLRO Wind Turbine Lightning Protection Test Lead Set MEG,DLRO-100LEAD (2662) AU For Megger DLRO 10 series digital microohm meters. Specially designed for measuring resistance of lightning protection circuit between wind turbine blade tip and ground. Kelvin clip and hook ends on 100m cable reel. 5m DH2 lead with duplex hand spikes and hook end. Megger DLRO Lead Set Current & Voltage Leads MEG,DLRO-LEADSET (2666) AU For Megger DLRO digital micro-ohm meters. Potential spike lead set x2 and current clip lead set x2. Leads are used to separate the C & P connections. This avoids the erroneously high readings taken due to a high resistance contact. Current clip lead set 2m (242041-7) and potential spike set 2m (242021-7). Megger MOM2 Micro-Ohm Meter MEG,MOM2 (2638) AU Lightweight (1kg), handheld micro-ohm meter. Up to 220A test current, autoranging from 999μΩ to 1000mΩ FS. Rechargable batteries provide 2200 measurements for Imin = 50A, or 800 for Imin = 100A. Memory for 190 recorded measurements, downloadable via Bluetooth with provided software. Kelvin probes included. New items are being added to the inventory constantly, so if you do not see what you are looking for please call 1800 632 652. Power Analysers, Loggers & Recorders See also Current Clamps Probes & Accessories on page 31-32 CHK GridSense PowerMonic PM20 Power Quality Analyser CHK,PM20 MY Three phase, weatherproof IP65 field unit. Three voltage channels 63V to 440V (isolated). F<strong>our</strong> current channels 0 to 3kA RMS (3ph & neutral). Supplied with 3 x 1kA clamp-on CTs (cable capacity 50mm), 3kA for large conductors and 500A for neutrals clamp-on CTs are available. Memory 4Mb. In-built 2 line LCD display. Records V, A, pf, f(Hz), kW, kVA, kVAr, THD, total energy and tariffs, high speed RMS waveform capture events outside preset limits (10ms intervals). Software provides graphs and summaries to PC. <strong>Download</strong> files while logging. RS232 interface. PC using Win 95, 98 or NT4 O/S, is required with the CHK POWERview software to configure this unit before operating. CHK Gridsense Powermonic PM30 Power Quality Analyser CHK,PM30 (8705) AU/MY Weatherproof IP65 field unit. Channels 3 voltage, 63V to 440V (isolated), 4 current 0 to 3kA (3ph & neutral) RMS. Supplied with 3 x 1kA clamp-on CTs (cable capacity 50mm). Clamp-on CTs of 3kA, 1kA for large conductors and 500A & 100A for neutral conductor current measurement are available. Memory 4Mb. In-built 2 line LCD display. Records V, A, pf, f(Hz), kVA, kVAr, kW, harmonics, (THD and individual to 48th). Total energy, tariffs, max demands, transient and sub-cycle disturbances. Software provides graphs and summaries to PC. <strong>Download</strong> files while logging via RS232 interface. PC using Win 95, 98, NT4, 2000, XP, O/S, is required with the CHK POWERview software to configure this unit before operating. CHK GridSense PowerMonic PM30 Plus Power Quality Analyser CHK,PM30PLUS (8706) AU/MY Weatherproof IP65 field unit. Channels: 3 Voltage, 63V to 440V (isolated). 3 current 0 to 3,000A (3ph) rms. Supplied with 3 flexible 3,000A clamp-on CTs (flexible CT length 600mm and 190mmØ). In addition, clamp-on CTs of 3,000A, 1,000A for large conductors and 500A and 100A for neutral conductor current measurement are available. Memory: 4Mb. Inbuilt two line LCD display. Records: V, A, pf, f(Hz), kVA, kVAr, kW, harmonics, (THD and individual to 48th). Total energy, tariffs, maximum demands, transient and sub-cycle disturbances. Included software provides graphs and summaries to PC. <strong>Download</strong> files while logging RS-232 interface. A PC using Windows 95, 98, NT4, WIN2000 or XP O/S, is required with the CHK POWERview software to configure this unit before operating. CHK GridSense PowerMonic PM35 Power Quality Analyser CHK,PM35 MY Power logger and disturbance analyser. Weatherproof IP65 field unit. 3 Voltage (55VAC to 520VAC) and 4 current (0 to 3,000A) channels. Supplied with 4 flexible 3,000A clamp-on CTs (flexible CT length 600mm and 190mmØ). Memory: 15Mb. Inbuilt two line LCD display. Records: V, A, pf, f(Hz), kVA, kVAr, kW, harmonics, (THD and individual to 48th). Flicker (Pst & Plt), Total energy, tariffs, maximum demands, transient and sub-cycle disturbances. Included software provides graphs and summaries to PC. <strong>Download</strong>s files while logging. High speed USB interface. A PC using Windows 95, 98, NT4, WIN2000 or XP (Vista in compatability mode)O/S, is required with the software to configure this unit before operating. 27
Change language