Sony - TSL

More documents

Recommendations

Info

6.0 General Notes for Displays It must be remembered that the Displays themselves will have to have their addresses set via the recessed buttons on the front panel. The single and dual displays require one address each whereas the triple and quad displays require two addresses each. For programming reasons Triple and Quad displays always start with an even address. This means that with a mixture of display types, not all addresses may be available. If a single D8C display is to be used as the Right display (please see the UMD Displays Manual) , i.e. it is required to display the second set of 8 characters in the 16 bytes sent, it should be entered into the program as a Dual 8 when a second line will be made available for mnemonics entry as Display 2. Only one address is needed for the LH and RH Displays, as would be the case for a genuine DD8C Display. This is a method of doubling the number of D8C Displays on the system for the set number of addresses. Using a single D16 or D16C as a combined router-associated and fixed display Sometimes it will be found useful to use a D16 display to indicate both router derived mnemonics and tallies and separately, a fixed mnemonic, so the cameraman’s name may be added to, say, the Cam 1 indication, which could be a Fixed Router Source mnemonic. The D16 display should be entered into Winsoft as a Dual 8. This will use only one address but will allow each half of the display (two times eight characters) to be separately assigned for mnemonic indication. The LH side of the display must have the required tally information mapped to it and it would normally also be the router-associated display. The RH side of the display may be used for an 8 character Fixed Mnemonic or other router mnemonic function. Displays with red/green display blocks For those special DD8 UMDs which use the first four blocks as red displays and the second as green displays (or vice versa), the unit must be treated as a Quad Display. These units will be assigned two addresses by the program, allowing separate messages to be assigned to the coloured blocks. Split Tally working for the TD8 and QD8 displays The standard Triple and Quad displays do not support split-tally working. Custom units that do support split tally working must be entered into Winsoft as the appropriate Triple or Quad display. The program will allow split tallies to be entered. However, when setting the address on the hardware, the first pair of displays will be on an even address, as shown in Winsoft, and the second display (or pair of displays in the case of a QD8) must have its address incremented by 1. E.g. A TD8 with split tallies may be at address 008. The second half of the display must be entered as 009. WinSoft V 4.2.4.0 47 Issue 5.3
7.0 Audio Monitoring Unit Setup <strong>TSL</strong> AMUs may be set up and monitored via this program. A right hand mouse button click on the LH side of the display (an AMU2882 in this example) will bring up the following menu. The selected AMU may be set-up via the Attributes menu item. View shows an AMUMD2882 View shows an ML1 Using the Mouse or Tab keys on the keyboard, it will be possible to select the item to be changed. When the unit is configured, the button will action the selection and clear this screen. WinSoft V 4.2.4.0 48 Issue 5.3
Page 1 and 2: WinSoft The TSL UMD Configuring Pro
Page 3 and 4: Section B WINSOFT CONTENTS Part A 1
Page 5 and 6: 11.0 Notes on the use of the 2 x 1
Page 7 and 8: A Monitor Stack WinSoft V 4.2.4.0 6
Page 9 and 10: Winsoft / System Controller Feature
Page 11 and 12: The cable required to connect the S
Page 13 and 14: Display Terminology ♦ Fixed Displ
Page 15 and 16: This is also the box which enables
Page 17 and 18: » To change double, triple and qua
Page 19 and 20: 2.1 Setting the Mnemonics - The Edi
Page 21 and 22: 2.1.2 Router Source and Bus Mnemoni
Page 23 and 24: 2.2.1 Router Bus Priority It is pos
Page 25 and 26: 2.4 Edit Display Assignment The com
Page 27 and 28: General The System Controller has D
Page 29 and 30: 2.5.1.1 Edit > Tallies > Edit Displ
Page 31 and 32: 2.5.3 Edit Router Source Tallies Ta
Page 33 and 34: 2.5.5 Edit Tally Input Attributes -
Page 35 and 36: External Enable - normally set to O
Page 37 and 38: Assign to Source A variation on the
Page 39 and 40: 3.2 Setup Menu 3.2.1 Options Under
Page 41 and 42: Configure Router Serial Port Change
Page 43 and 44: 3.6.1 The Lists and Mnemonics The L
Page 45 and 46: 4.0 Associating Monitors with a Rou
Page 47: 5.0 Desktop Enhancements 5.1 Making
Page 51 and 52: 8.0 The Help Menu 8.1 About Winsoft
Page 53 and 54: 9.2 Configure Names Options 9.2.1 R
Page 55 and 56: Mixer Mnemonics Only Labels can (wh
Page 57 and 58: 11.0 Notes on the use of the 2 x 1
Page 59 and 60: Setting Tallies Set tallies to the

Sony - TSL

Create successful ePaper yourself

Delete template?

Save as template?